DTC C1681 is stored if the parking assist ECU judges as a result of ifs self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1681 | Front television camera power supply failure | ·
Harness or connector ·
Front television camera assembly ·
Parking assist ECU |
When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the F76 parking assist ECU connector.
Disconnect the A71 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-36 (BCV-) - A71-2 (BCV-) | Always | Below 1 Ω |
| F76-12 (BCV+) - A71-3 (BCV+) | Always | Below 1 Ω |
| F76-35 (BGND) - A71-5 (BGND) | Always | Below 1 Ω |
| F76-11 (BCB+) - A71-6 (BCB+) | Always | Below 1 Ω |
| F76-34 (SGND) - Body ground | Always | Below 1 Ω |
| F76-36 (BCV-) - Body ground | Always | 10 kΩ or higher |
| F76-12 (BCV+) - Body ground | Always | 10 kΩ or higher |
| F76-35 (BGND) - Body ground | Always | 10 kΩ or higher |
| F76-11 (BCB+) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 35 (BGND) - Body ground | Always | Below 1 Ω |
| 36 (BCV-) - Body ground | Always | Below 1 Ω |
| *a | Component without harness connected
(Parking Assist ECU) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-35 (BGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F76-11 (BCB+) - F76-35 (BGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| *a | Component with harness connected
(Parking Assist ECU) |
OK
NG
Check the ware form of the front television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the front television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F76-12 (BCV+) - F76-35 (BGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), main switch assembly (multi-terrain monitor main switch) on and camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), main switch assembly (multi-terrain monitor main switch) on and camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
OK
NG