| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| U0265 | Lost Communication with rear television camera assembly | ·
Parking assist ECU ·
Rear television camera assembly ·
CAN junction connector ·
CAN junction terminal ·
CAN main wire or connector ·
CAN branch wire or connector |
| U0266 | Lost Communication with side television camera assembly LH | ·
Parking assist ECU ·
Side television camera assembly LH ·
CAN junction connector ·
CAN junction terminal ·
CAN main wire or connector ·
CAN branch wire or connector |
| U0267 | Lost Communication with front television camera assembly | ·
Parking assist ECU ·
Front television camera assembly ·
CAN junction connector ·
CAN junction terminal ·
CAN main wire or connector ·
CAN branch wire or connector |
| U0268 | Lost Communication with side television camera assembly RH | ·
Parking assist ECU ·
Side television camera assembly RH ·
CAN junction connector ·
CAN junction terminal ·
CAN main wire or connector ·
CAN branch wire or connector |
Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC U0265, U0266, U0267 and U0268 are not output | A |
| DTC U0265, U0266, U0267 and U0268 are output | B |
| DTC U0265, U0266, U0267 or U0268 are output | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-21 (CANH) - F76-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F76-21 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F76-20 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F76-21 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F76-20 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Reconnect the F76 parking assist ECU connector.
NEXT
Disconnect the CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (CANH) - K51-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| K51-3 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K51-2 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K51-3 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K51-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *a | Rear view of harness connector
(to CAN Junction Terminal) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the K51 CAN junction terminal connector.
NEXT
Disconnect the No. 8 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | Parking Assist ECU | *d | No. 10 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E153-1 (CANH) - E153-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Parking Assist ECU |
| E153-1 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E153-11 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E153-1 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E153-11 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E153-3 (CANH) - E153-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 10 CAN Junction Connector |
| E153-3 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E153-13 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E153-3 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E153-13 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to parking assist ECU CAN main wire) | B |
| NG (to No. 10 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the E153 No. 8 CAN junction connector.
NEXT
Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the No. 10 CAN junction connector.
| *1 | No. 10 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 10 CAN Junction Connector) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| K54-1 (CANH) - K54-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 8 Junction Connector |
| K54-1 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| K54-2 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| K54-1 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| K54-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| K55-1 (CANH) - K55-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN Junction Terminal |
| K55-1 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| K55-2 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| K55-1 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| K55-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to No. 8 CAN junction connector CAN main wire) | B |
| NG (to CAN junction terminal CAN main wire) | C |
A
B
C
Which the DTCs have been output from.
| Result | Proceed to |
|---|---|
| DTC U0265 is output | A |
| DTC U0266 is output | B |
| DTC U0267 is output | C |
| DTC U0268 is output | D |
A
B
C
D
Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the No. 10 CAN junction connector.
| *1 | No. 10 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 10 CAN Junction Connector) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K53-1 (CANH) - K53-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K53-1 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K53-2 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K53-1 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K53-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Reconnect the K53 No. 10 CAN junction connector.
NEXT
Disconnect the rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-4 (CANH) - S30-1 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| S30-4 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S30-1 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S30-4 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S30-1 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Disconnect the No. 8 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E153-5 (CANH) - E153-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-5 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-15 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-5 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E153-15 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Reconnect the E153 No. 8 CAN junction connector.
NEXT
Disconnect the side television camera assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I32-3 (CANH) - I32-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I32-3 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I32-14 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I32-3 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I32-14 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Disconnect the No. 8 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E153-2 (CANH) - E153-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-2 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-12 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-2 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E153-12 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Reconnect the E153 No. 8 CAN junction connector.
NEXT
Disconnect the front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A71-4 (CANH) - A71-1 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A71-4 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A71-1 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A71-4 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A71-1 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Disconnect the No. 8 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E153-4 (CANH) - E153-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-4 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-14 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E153-4 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E153-14 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG
Reconnect the No. 8 CAN junction connector.
NEXT
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I35-3 (CANH) - I35-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I35-3 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I35-14 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I35-3 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I35-14 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OK
NG