Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E333584E05
0.865,5.292 2.854,5.531 1.99,0.24 10 false : CAN Communication Line 2.292,0.875 2.865,1.24 0.573,0.365 10 false ECU-IG NO. 3 3.594,0.719 4.052,0.917 0.458,0.198 10 false BRB 3.615,1.521 4.073,1.719 0.458,0.198 10 false BRGD 3.604,4.115 4.063,4.313 0.458,0.198 10 false BRGD 3.615,3.292 4.073,3.49 0.458,0.198 10 false BRB 0.26,0.688 1.948,0.885 1.688,0.198 10 false from IG1 NO. 2 Relay 3.552,4.594 3.865,4.792 0.313,0.198 10 false r1 3.552,4.792 4.698,5.167 1.146,0.375 10 false Blind Spot Monitor Sensor RH 3.396,2 3.708,2.198 0.313,0.198 10 false r2 3.406,2.177 4.563,2.625 1.156,0.448 10 false Blind Spot Monitor Sensor LH 3.375,0.573 3.531,0.771 0.156,0.198 10 false 5 3.375,3.156 3.531,3.354 0.156,0.198 10 false 5 3.333,1.365 3.646,1.563 0.313,0.198 10 false 10 3.323,3.958 3.635,4.156 0.313,0.198 10 false 10 6,0.854 6.573,1.083 0.573,0.229 10 false to CAN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH, BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U166460E02
1.958,1.26 2.406,0.844 2.406,0.844 2.625,0.844 true 1.958,1.51 2.385,2.031 2.385,2.031 2.604,2.031 true 1.948,3.563 2.396,3.146 2.396,3.146 2.615,3.146 true 1.958,3.792 2.385,4.313 2.385,4.313 2.604,4.313 true 0.146,0.094 0.51,0.344 0.365,0.25 10 false *a 1.646,0.417 2.01,0.594 0.365,0.177 10 false r1 2.667,3.063 3.031,3.24 0.365,0.177 10 false BRB 1.646,2.698 2,2.938 0.354,0.24 10 false r2 2.677,4.229 3.156,4.448 0.479,0.219 10 false BRGD 0.125,2.385 0.49,2.635 0.365,0.25 10 false *b 2.698,0.76 3.063,0.938 0.365,0.177 10 false BRB 2.688,1.958 3.135,2.135 0.448,0.177 10 false BRGD

Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r2-10 (BRGD) - Body ground Always Below 1 Ω
r1-10 (BRGD) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r2-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V
r2-5 (BRB) - Body ground Engine switch off Below 1 V
r1-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V
r1-5 (BRB) - Body ground Engine switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR