Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255517 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


CHECK REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the S31 rear television camera assembly connector.

U166461E02
3.458,0.135 3.771,0.344 0.313,0.208 10 false S31


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S31-6 (CB+) - Body ground B - Body ground Power source Engine switch on (ACC) 5.5 to 7.05 V


c.

Reconnect the S31 rear television camera assembly connector.


d.

Measure the voltage and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S31-3 (CV+) - S31-2 (CV-) R - W Video signal Engine switch on (IG)
Shift lever in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Engine switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
S31-5 (CGND) - Body ground L - Body ground Shield ground Always Below 1 V

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.



e.
E265840E16
1.271,1.479 1.531,2.063 false 1.104,1.583 0.875,2.052 false 1.323,3.521 1.646,4.208 false 1.135,3.594 0.844,4.219 false 0.083,0.042 0.281,0.229 0.198,0.188 10 false *a 0.094,2.219 0.292,2.406 0.198,0.188 10 false *b 0.365,1.042 0.74,1.271 0.375,0.229 10 false GND 0.354,3.208 0.719,3.448 0.365,0.24 10 false GND 0.771,2.052 0.969,2.24 0.198,0.188 10 false *c 1.49,2.063 1.688,2.25 0.198,0.188 10 false *d 1.604,4.219 1.802,4.406 0.198,0.188 10 false *d 0.75,4.219 0.948,4.406 0.198,0.188 10 false *c

Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the accessory meter assembly*1 or multi-display assembly*2 with the connector connected.


Text in Illustration
*a Waveform 1
*b Waveform 2
*c Synchronization Signal
*d Video Waveform

i.

Waveform 1

Item Content
Terminal No. (Symbol) S31-3 (CV+) - S31-2 (CV-)
Tool setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG)
Shift lever in R
Camera lens not covered, displaying image

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).




ii.

Waveform 2

Item Content
Terminal No. (Symbol) S31-3 (CV+) - S31-2 (CV-)
Tool setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG)
Shift lever in R
Camera lens covered, blacking out screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).








MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU)



MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/o Navigation System) (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>TERMINALS OF ECU)