Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255517 PARKING ASSIST MONITOR SYSTEM D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE


a.

In diagnostic mode for the parking assist monitor system, signals received by the radio receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the multi-display assembly with the connector connected.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E340062E02
2.958,1.125 4.344,1.438 1.385,0.313 10 false Start diagnostic mode

E340063


DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E340064E02
2.927,0.906 4.417,1.177 1.49,0.271 10 false Start diagnostic mode

E340065


VEHICLE SIGNAL CHECK


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



b.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/ Setting I" screen.


c.
E339651

Select "Vehicle Signal" on the "Function Check/ Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".


HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the multi-media module receiver assembly.







CAR SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/ Setting I" screen.


ii.
E339651

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the rear television camera assembly was replaced.

Parking Assist Monitor System Initialization Screen Transition
Not performed Car Signal Check screen
Performed Mode Setting screen



iii.
E276139

When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E276130

Car Signal Check

i.

On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
BCTY Back door courtesy light switch signal input When "CHK" (red) is displayed, selecting "Next" will not change the screen to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

BCTY inspection

HINT:

If "CHK" (red) is displayed for "BCTY", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR).





CAMERA SYNCHRONOUS ERROR HISTORY


HINT:

This function is used to check the date and time of occurrence when a camera synchronous error occurs.


a.

Check camera synchronous error history.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Camera Synchronous Error History.


v.

When an item is stored for Camera Synchronous Error History, record it before repairing the multi-media module receiver assembly and rear television camera assembly.

HINT:

Camera Synchronous Error History can store up to 5 history data items. If a new camera synchronous error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.




b.

Clear camera synchronous error history.

i.

When DTCs are cleared using any of the following operations, Camera Synchronous Error History will be cleared as well.


·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.






CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION).