Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR (for 100 A Type)
RM2660E _57 Power Source / Network _052832 1GR-FE BATTERY / CHARGING _0255520 GENERATOR(for 100 A Type) A

1GR-FE BATTERY / CHARGING  GENERATOR(for 100 A Type)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A219656

Using a screwdriver, remove the generator pulley cap.


Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator in a vise between aluminum plates.


b.
A219555E01
2.384,0.291 2.577,0.466 0.193,0.174 10 *1 1.521,1.673 2.063,1.828 0.541,0.155 10 SST (A) 2.113,1.415 2.647,1.570 0.534,0.155 10 SST (A) 1.441,0 1.994,0.155 0.553,0.155 10 SST (B) 1.224,0.884 1.32,0.076 1.32,0.076 1.432,0.076 false 1.304,1.184 1.384,1.749 1.384,1.749 1.51,1.749 false 2.118,0.785 2.233,0.379 2.233,0.379 2.37,0.379 false 3.078,1.155 2.889,1.52 2.889,1.52 2.758,1.52 false

Install SST (A) and SST (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

Text in Illustration
*1 Rotor Shaft

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



c.
A219556E01
2.49,0.142 3.027,0.301 0.538,0.159 10 SST (B) 2.49,0.507 3.047,0.666 0.557,0.159 10 SST (A) 1.832,1.873 2.012,2.033 0.180,0.159 10 *a 1.96,0.62 2.379,0.246 2.379,0.246 2.467,0.246 false 2.205,0.831 2.378,0.611 2.378,0.611 2.467,0.611 false

Use a wrench to hold SST (A) and turn SST (B) counterclockwise to loosen the generator pulley with clutch.

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator.


e.

Remove the generator pulley with clutch from the rotor shaft.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A221621

Remove the nut and cord clip.


b.
A220458

Remove the 3 nuts and generator rear end cover.


Hide 27387 4.REMOVE TERMINAL INSULATOR

a.
A219659

Remove the terminal insulator from the generator coil.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A219660

Remove the 2 screws and brush holder from the generator coil.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A219661

Remove the 4 bolts.


b.
A219662E01
0.8,0.351 0.991,0.524 0.191,0.174 10 *a 2.618,0.594 2.929,0.759 0.311,0.165 10 SST 2.083,0.818 2.513,0.683 2.513,0.683 2.601,0.683 false

Using SST, remove the generator coil.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
V100135

Turn


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
U113562E01
2.194,0.179 2.063,0.309 false

Remove the generator washer.


b.
A219665

Remove the generator rotor.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A128080

Check that the drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A223426

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A128077E01
0.187,0.662 0.485,0.807 0.298,0.145 10 SST 1.308,0.98 0.573,0.778 0.573,0.778 1.249,1.236 false

Using SST and a hammer, tap out the drive end frame bearing from the generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)