Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR(for 130 A Type) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052832 1GR-FE BATTERY / CHARGING _0255521 GENERATOR(for 130 A Type) G

1GR-FE BATTERY / CHARGING  GENERATOR(for 130 A Type)  INSPECTION  


PROCEDURE

Hide 27415 1.INSPECT GENERATOR PULLEY WITH CLUTCH

a.
A267550E01
0.148,1.275 0.456,1.429 0.309,0.155 10 SST 0.518,1.349 0.667,1.349 0.667,1.349 0.792,1.534 false 0.587,1.854 0.771,2.009 0.184,0.155 10 *a

Using SST, hold the center of the generator pulley with clutch and check that the outer ring turns counterclockwise and does not turn clockwise.

SST
09820-63021  

Text in Illustration
*a Hold
V100135

Free
V100136

Lock

If the result is not as specified, replace the generator pulley with clutch.


Hide 27370 2.INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

a.
A128079E06
0.693,0.687 0.870,0.857 0.177,0.170 10 *1

Using a vernier caliper, measure the brush length.

Standard exposed length:

9.5 to 11.5 mm (0.374 to 0.453 in.)


Minimum exposed length:

4.5 mm (0.177 in.)


Text in Illustration
*1 Length

If the brush length is less than the minimum, replace the generator brush holder assembly.


Hide 27330 3.INSPECT GENERATOR ROTOR ASSEMBLY

a.
A079306

Check that the generator rotor bearing is not rough or worn.

If necessary, replace the generator rotor assembly.


b.

Check the resistance.

i.
B012264E54
0.365,1.146 0.854,0.125 0.854,0.125 0.958,0.125 false 1.031,0.063 1.198,0.219 0.167,0.156 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 2.3 to 2.7 Ω


Text in Illustration
*1 Slip Ring

If the result is not as specified, replace the generator rotor assembly.


ii.
B012265E47
0.354,1.115 0.542,0.156 0.542,0.156 0.646,0.156 true 1.073,0.813 1.385,0.417 1.385,0.417 1.469,0.417 true 0.667,0.094 0.854,0.271 0.188,0.177 10 false *1 1.542,0.344 1.729,0.521 0.188,0.177 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Slip ring - Rotor core Always 10 MΩ or higher


Text in Illustration
*1 Slip Ring
*2 Rotor Core

If the result is not as specified, replace the generator rotor assembly.



c.
A124106E04
0.658,0.485 0.837,0.638 0.179,0.154 10 *1

Using a vernier caliper, measure the slip ring diameter.

Standard diameter:

14.2 to 14.8 mm (0.559 to 0.583 in.)


Minimum diameter:

14.0 mm (0.551 in.)


Text in Illustration
*1 Diameter

If the diameter is less than the minimum, replace the generator rotor assembly.