Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR(for 130 A Type) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052832 1GR-FE BATTERY / CHARGING _0255521 GENERATOR(for 130 A Type) A

1GR-FE BATTERY / CHARGING  GENERATOR(for 130 A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A219663E01
0.045,0.408 0.358,0.580 0.313,0.172 10 SST 1.011,1.059 0.634,0.503 0.634,0.503 0.423,0.503 false 0.95,1.196 0.497,0.504 false

Using SST and a press, press in a new drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A219664E01
1.768,0.161 1.954,0.312 0.186,0.151 10 *1 1.768,0.716 1.954,0.867 0.186,0.151 10 *2 2.832,1.427 2.075,0.796 2.075,0.796 1.987,0.796 false 2.832,1.061 2.075,0.245 2.075,0.245 1.987,0.245 false

Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.

Text in Illustration
*1 Tab
*2 Cutout


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the generator rotor to the generator drive end frame.


b.

Place a new generator washer on the generator rotor.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A128082E07
0.869,0.091 1.042,0.247 0.173,0.156 10 *1 1.61,0.618 1.175,0.183 1.175,0.183 1.065,0.183 false

Using a deep socket wrench (21 mm) and press, slowly press in the generator coil.

Text in Illustration
*1 Deep Socket Wrench (21 mm)


b.

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079315E20
3.01,2.016 3.414,2.147 0.404,0.131 1.35,0.307 1.527,0.474 0.177,0.166 10 *1 0.983,0.733 1.255,0.4 1.255,0.4 1.341,0.4 false

While pushing the 2 brushes into the brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.

Text in Illustration
*1 Pin


b.
U147548E01
2.132,0.375 2.314,0.523 0.182,0.148 10 *1 1.931,0.631 2.035,0.451 2.035,0.451 2.127,0.451 false

Install the brush holder to the generator coil with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)

Text in Illustration
*1 Pin


c.

Pull out the pin from the brush holder.


Hide 27387 5.INSTALL TERMINAL INSULATOR

a.
A219668

Install the terminal insulator to the generator coil.

NOTICE:

Make sure the terminal insulator is installed facing the proper direction.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


b.

Install the cord clip with the nut.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 27415 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Temporarily install the generator pulley with clutch by hand.


b.

Mount the generator in a vise between aluminum plates.


c.
A219555E01
2.384,0.291 2.577,0.466 0.193,0.174 10 *1 1.521,1.673 2.063,1.828 0.541,0.155 10 SST (A) 2.113,1.415 2.647,1.570 0.534,0.155 10 SST (A) 1.441,0 1.994,0.155 0.553,0.155 10 SST (B) 1.224,0.884 1.32,0.076 1.32,0.076 1.432,0.076 false 1.304,1.184 1.384,1.749 1.384,1.749 1.51,1.749 false 2.118,0.785 2.233,0.379 2.233,0.379 2.37,0.379 false 3.078,1.155 2.889,1.52 2.889,1.52 2.758,1.52 false

Install SST (A) and SST (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

Text in Illustration
*1 Rotor Shaft

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



d.
A219557E02
0.016,1.137 0.581,1.284 0.564,0.147 10 SST (A) 0.75,2.352 0.919,2.499 0.169,0.147 10 *a 0.019,0.019 0.567,0.165 0.549,0.147 10 SST (B) 1.004,0.641 0.774,0.102 0.774,0.102 0.682,0.102 false 0.645,0.94 0.306,1.039 0.306,1.039 0.306,1.13 false 1.24,2.088 1.417,2.248 0.177,0.160 10 *1

Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley with clutch.

Torque:
without SST : 80 N*m (816 kgf*cm, 59 ft.*lbf)
with SST : 64 N*m (653 kgf*cm, 47 ft.*lbf)

Text in Illustration
*1 Fulcrum Length
*a Hold
V100135

Turn

NOTICE:

Be careful as the generator pulley with clutch or rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




e.

Remove SST from the generator.


f.

Check that the generator pulley with clutch rotates smoothly.


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.