Home › Power Source / Network › 1UR-FE (BATTERY / CHARGING) › GENERATOR (for 130 A, 150 A Type)
RM2660E _57 Power Source / Network _052835 1UR-FE BATTERY / CHARGING _0255527 GENERATOR(for 130 A, 150 A Type) A

1UR-FE BATTERY / CHARGING  GENERATOR(for 130 A, 150 A Type)  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator in a vise between aluminum plates.


b.
U115370E03
3.052,1.167 3.052,0.635 false 2.438,1.542 2.438,1.302 2.438,1.302 2.854,0.708 false 1.719,1.813 1.896,1.979 0.177,0.167 10 false *a 2.198,1.552 2.75,1.698 0.552,0.146 10 false SST 1-B 2.781,1.188 3.333,1.333 0.552,0.146 10 false SST 1-A

Install SST 1-A to the pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021



c.

Insert SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Check that SST is secured on the rotor shaft.



e.
A187036E04
2,0.291 2.443,0.458 0.443,0.166 10 SST 2 2.531,0.376 2.663,0.376 2.663,0.376 2.825,0.884 false

Insert SST 2 and attach it to the pulley nut.

Text in Illustration
V100135

Insert


f.
U115371E01
2.515,1.703 2.696,1.868 0.181,0.165 10 *b 1.891,1.688 2.070,1.849 0.179,0.161 10 *a

To loosen the pulley nut, turn SST 1-A in the direction shown in the illustration.

Text in Illustration
*a Hold
*b Turn

NOTICE:

To prevent damage to the rotor shaft, do not loosen the pulley nut more than one-half turn.



g.

Remove SST 2 from the generator.


h.
U115372E03
3.073,1.177 3.073,0.667 false 2.635,1.521 2.635,1.302 2.635,1.302 2.885,0.708 false 2,1.604 2.167,1.76 0.167,0.156 10 false *a 2.344,1.563 2.917,1.781 0.573,0.219 10 true SST 1-B 2.813,1.188 3.365,1.344 0.552,0.156 10 false SST 1-A

Turn SST 1-B in the direction shown in the illustration, and then remove SST 1-A and SST 1-B.

Text in Illustration
*a Hold
V100135

Turn


i.

Remove the pulley nut and generator pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A230483

Remove the 3 nuts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

A230484

Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A230485

Remove the 2 screws and brush holder.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A230486

Remove the 4 bolts.


b.
U115336E01
0.354,0.384 0.723,0.630 0.369,0.246 10 SST 0.378,1.494 0.565,1.661 0.187,0.167 10 *a 1.327,0.83 0.957,0.466 0.957,0.466 0.755,0.466 false

Using SST, remove the generator coil.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
V100135

Turn


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A156421

Remove the generator washer.


b.
A230487

Remove the generator rotor.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A156418

Check that the drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A156416

Remove the 4 screws and retainer plate.


b.
A156417E01
2.377,0.955 2.721,1.136 0.344,0.181 10 SST 1.673,1.377 2.333,1.042 false 2.333,1.042 1.68,0.979 false

Using SST and a hammer, tap out the drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)