Home › Power Source / Network › 1UR-FE (BATTERY / CHARGING) › GENERATOR (for 180 A Type)
RM2660E _57 Power Source / Network _052835 1UR-FE BATTERY / CHARGING _0255528 GENERATOR(for 180 A Type) A

1UR-FE BATTERY / CHARGING  GENERATOR(for 180 A Type)  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A297263E05
2.115,0.229 2.229,0.229 2.229,0.229 2.771,0.469 false 2.865,1.281 2.979,1.281 2.979,1.281 3.063,0.615 false 1.688,1.917 1.865,2.104 0.177,0.188 10 false *a 1.458,0.146 2.021,0.333 0.563,0.188 10 false SST 1-B 2.25,1.198 2.802,1.385 0.552,0.188 10 false SST 1-A

Install SST 1-A and SST 1-B to the rotor shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and SST 1-B 09820-06010
SST 2 09820-06021



c.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Check that SST is secured on the rotor shaft.



d.
A297264E01
2.037,0.201 2.446,0.366 0.409,0.165 10 SST 2 2.551,0.294 2.748,0.294 2.748,0.294 2.748,0.866 false

Insert SST 2 and attach it to the pulley nut.

Text in Illustration
V100135

Insert


e.
A297265E01
1.522,1.76 1.697,1.927 0.175,0.167 10 *a 2.382,1.731 2.556,1.898 0.175,0.167 10 *b

To loosen the pulley nut, turn SST 1-A in the direction shown in the illustration.

Text in Illustration
*a Hold
*b Turn

NOTICE:

To prevent damage to the rotor shaft, do not loosen the pulley nut more than one-half turn.



f.

Remove SST 2.


g.
A297266E01
2.329,1.737 2.531,1.916 0.202,0.178 10 *a 2.228,1.219 2.783,1.397 0.555,0.178 10 SST 1-B 2.911,1.306 3.02,1.306 3.02,1.306 3.02,0.727 false 1.455,0.088 2.016,0.267 0.561,0.178 10 SST 1-A 2.145,0.176 2.255,0.176 2.255,0.176 2.988,0.54 false

Turn SST 1-B in the direction shown in the illustration, and then remove SST 1-A and SST 1-B.

Text in Illustration
*a Hold
V100135

Turn


h.

Remove the pulley nut and generator pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A297267

Remove the 3 nuts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

A230484

Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A230485

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A230486

Remove the 4 bolts.


b.
U115336E01
0.354,0.384 0.723,0.630 0.369,0.246 10 SST 0.378,1.494 0.565,1.661 0.187,0.167 10 *a 1.327,0.83 0.957,0.466 0.957,0.466 0.755,0.466 false

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
V100135

Turn


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A156421

Remove the generator washer.


b.

Remove the generator rotor assembly.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A156418

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A156416

Remove the 4 screws and retainer plate.


b.
A156417E01
2.377,0.955 2.721,1.136 0.344,0.181 10 SST 1.673,1.377 2.333,1.042 false 2.333,1.042 1.68,0.979 false

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)