Home › Power Source / Network › 1UR-FE (BATTERY / CHARGING) › GENERATOR (for 180 A Type)
RM2660E _57 Power Source / Network _052835 1UR-FE BATTERY / CHARGING _0255528 GENERATOR(for 180 A Type) A

1UR-FE BATTERY / CHARGING  GENERATOR(for 180 A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A156419E01
2.872,0.516 3.203,0.707 0.331,0.190 10 SST 1.752,0.766 2.825,0.586 false 2.825,0.586 1.891,1.212 false

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00500)
09950-70010  (09951-07100)


b.

Install the retainer plate with the 4 screws.

Torque:
3.0 N*m (30 kgf*cm, 26 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the generator rotor assembly to the generator drive end frame assembly.


b.

Place a new generator washer on the generator rotor assembly.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A156422

Using a 22 mm socket wrench and press, slowly press in the generator coil assembly.


b.

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A163049E02
1.382,0.062 1.572,0.218 0.191,0.156 10 *1 0.926,0.535 1.274,0.149 1.274,0.149 1.377,0.149 false

While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the generator brush holder assembly hole.

Text in Illustration
*1 Pin


b.
A156423E04
2.88,0.189 3.068,0.364 0.188,0.174 10 *1 1.791,0.863 2.626,0.275 2.626,0.275 2.816,0.275 false

Install the generator brush holder assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.

Text in Illustration
*1 Pin


Hide 27387 5.INSTALL TERMINAL INSULATOR

a.

Install the terminal insulator to the generator coil assembly.

NOTICE:

Pay attention to the mounting orientation of the terminal insulator.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


Hide 27411 7.INSTALL GENERATOR PULLEY

a.

Temporarily install the generator pulley with the pulley nut by hand.


b.

Mount the generator assembly in a vise between aluminum plates.


c.
A297263E05
2.115,0.229 2.229,0.229 2.229,0.229 2.771,0.469 false 2.865,1.281 2.979,1.281 2.979,1.281 3.063,0.615 false 1.688,1.917 1.865,2.104 0.177,0.188 10 false *a 1.458,0.146 2.021,0.333 0.563,0.188 10 false SST 1-B 2.25,1.198 2.802,1.385 0.552,0.188 10 false SST 1-A

Install SST 1-A and SST 1-B to the rotor shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021



d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Check that SST is secured to the rotor shaft.



e.
A297264E01
2.037,0.201 2.446,0.366 0.409,0.165 10 SST 2 2.551,0.294 2.748,0.294 2.748,0.294 2.748,0.866 false

Insert SST 2 and attach it to the pulley nut.

Text in Illustration
V100135

Insert


f.
A270461E01
1.297,1.875 1.456,2.054 0.159,0.179 10 *a 2.002,1.902 2.161,2.053 0.159,0.151 10 *b

Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

Torque:
133 N*m (1351 kgf*cm, 98 ft.*lbf)

Text in Illustration
*a Hold
*b Turn

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



g.

Remove SST 2.


h.
A297266E01
2.329,1.737 2.531,1.916 0.202,0.178 10 *a 2.228,1.219 2.783,1.397 0.555,0.178 10 SST 1-B 2.911,1.306 3.02,1.306 3.02,1.306 3.02,0.727 false 1.455,0.088 2.016,0.267 0.561,0.178 10 SST 1-A 2.145,0.176 2.255,0.176 2.255,0.176 2.988,0.54 false

Turn SST 1-B in the direction shown in the illustration, and then remove SST 1-A and SST 1-B.

Text in Illustration
*a Hold
V100135

Turn


i.

Turn the generator pulley and check that the pulley moves smoothly.