Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

For vehicle with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the Ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





JUNCTION CONNECTOR


a.

NO. 1 JUNCTION CONNECTOR

U164997E02
4.552,1.229 4.438,1.229 4.438,1.229 4.229,1.469 false 4.094,1.469 4.406,1.01 4.406,1.01 4.531,1.01 false 3.969,1.469 4.333,0.792 4.333,0.792 4.49,0.792 false 4.5,1.906 4.375,1.906 4.375,1.906 4.208,1.719 false 4.094,1.729 4.302,2.083 4.302,2.083 4.438,2.083 false 3.979,1.729 4.188,2.26 4.188,2.26 4.313,2.26 false 3.844,1.469 4.323,0.583 4.323,0.583 4.448,0.583 false 3.708,1.469 4.135,0.354 4.135,0.354 4.292,0.354 false 3.844,1.729 4.042,2.448 4.042,2.448 4.177,2.448 false 3.708,1.729 3.917,2.625 3.917,2.625 4.073,2.625 false 3.469,0.26 3.833,0.49 0.365,0.229 10 false E72 4.583,0.938 5.177,1.125 0.594,0.188 10 false CANH*b 4.542,0.708 5.125,0.906 0.583,0.198 10 false CANH*c 4.49,0.5 5.073,0.698 0.583,0.198 10 false CANH*d 4.333,0.281 4.927,0.469 0.594,0.188 10 false CANH*e 4.594,1.156 5.198,1.385 0.604,0.229 10 false CANH*a 4.542,1.844 5.146,2.021 0.604,0.177 10 false CANL*a 4.49,2.01 5.073,2.188 0.583,0.177 10 false CANL*b 4.354,2.188 4.896,2.385 0.542,0.198 10 false CANL*c 4.229,2.375 4.823,2.552 0.594,0.177 10 false CANL*d 4.125,2.563 4.708,2.75 0.583,0.188 10 false CANL*e

Text in Illustration
*a for No. 2 Junction Connector *b for ECM
*c for Headlight Swivel ECU Assembly (w/ Dynamic Headlight Auto Leveling) *d for Center Airbag Sensor Assembly (w/ Airbag System)
*e for 4WD Control ECU (w/o Network Gateway ECU) - -

No. 1 Junction Connector Wiring Color Connect to
E72-1 (CANH) Y*4, SB*5 No. 2 junction connector
E72-12 (CANL) B
E72-2 (CANH) P ECM
E72-13 (CANL) B
E72-3 (CANH) LG Headlight swivel ECU assembly*1
E72-14 (CANL) B
E72-4 (CANH) GR Center airbag sensor assembly*2
E72-15 (CANL) B
E72-5 (CANH) P 4WD control ECU*3
E72-16 (CANL) L

*1: w/ Dynamic Headlight Auto Leveling

*2: w/ Airbag System

*3: w/o Network Gateway ECU

*4: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*5: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



b.

NO. 2 JUNCTION CONNECTOR

U164998E02
4.552,1.229 4.427,1.229 4.427,1.229 4.219,1.469 false 4.115,1.469 4.417,1.01 4.417,1.01 4.552,1.01 false 3.958,1.469 4.323,0.792 4.323,0.792 4.479,0.792 false 4.51,1.917 4.385,1.917 4.385,1.917 4.219,1.729 false 4.083,1.729 4.292,2.083 4.292,2.083 4.417,2.083 false 3.969,1.729 4.177,2.26 4.177,2.26 4.313,2.26 false 3.833,1.469 4.302,0.583 4.302,0.583 4.438,0.583 false 3.708,1.469 4.135,0.354 4.135,0.354 4.292,0.354 false 3.833,1.729 4.031,2.448 4.031,2.448 4.156,2.448 false 3.708,1.729 3.917,2.625 3.917,2.625 4.083,2.625 false 3.469,0.271 3.781,0.521 0.313,0.25 10 false E69 4.583,0.938 5.188,1.156 0.604,0.219 10 false CANH*b 4.51,0.729 5.083,0.927 0.573,0.198 10 false CANH*c 4.479,0.51 5.083,0.729 0.604,0.219 10 false CANH*d 4.333,0.281 4.896,0.469 0.563,0.188 10 false CANH*e 4.604,1.177 5.167,1.385 0.563,0.208 10 false CANH*a 4.552,1.833 5.125,2.01 0.573,0.177 10 false CANL*a 4.469,2 5.031,2.208 0.563,0.208 10 false CANL*b 4.354,2.188 4.938,2.365 0.583,0.177 10 false CANL*c 4.198,2.375 4.792,2.573 0.594,0.198 10 false CANL*d 4.135,2.552 4.688,2.74 0.552,0.188 10 false CANL*e

Text in Illustration
*a for No. 1 Junction Connector *b for Multi-media Module Receiver Assembly (w/ Navigation System)
*c for Network Gateway ECU (V Bus) (w/ Network Gateway ECU) *d
·

for No. 3 Junction Connector (w/ Network Gateway ECU)

·

for No. 6 Junction Connector (w/o Network Gateway ECU)


*e for Air Conditioning Amplifier Assembly - -

No. 2 Junction Connector Wiring Color Connect to
E69-1 (CANH) Y*4, SB*5 No. 1 junction connector
E69-12 (CANL) B
E69-2 (CANH) P Multi-media module receiver assembly*1
E69-13 (CANL) B
E69-3 (CANH) BR*4, BE*5 Network gateway ECU (V bus)*2
E69-14 (CANL) B
E69-4 (CANH) W*2, *4
Y*3, *4
SB*5
·

No. 3 junction connector*2

·

No. 6 junction connector*3


E69-15 (CANL) B*2
L*3
E69-5 (CANH) G Air conditioning amplifier assembly
E69-16 (CANL) B

*1: w/ Navigation System

*2: w/ Network Gateway ECU

*3: w/o Network Gateway ECU

*4: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*5: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



c.

NO. 3 JUNCTION CONNECTOR

U164999E02
4.552,1.229 4.438,1.229 4.438,1.229 4.229,1.469 false 4.104,1.469 4.417,1.01 4.417,1.01 4.542,1.01 false 3.958,1.469 4.323,0.792 4.323,0.792 4.479,0.792 false 4.5,1.906 4.375,1.906 4.375,1.906 4.208,1.719 false 4.094,1.719 4.302,2.073 4.302,2.073 4.438,2.073 false 3.948,1.719 4.156,2.25 4.156,2.25 4.281,2.25 false 3.813,1.469 4.292,0.583 4.292,0.583 4.417,0.583 false 3.708,1.458 4.135,0.344 4.135,0.344 4.292,0.344 false 3.833,1.719 4.031,2.438 4.031,2.438 4.167,2.438 false 3.708,1.719 3.917,2.615 3.917,2.615 4.073,2.615 false 3.469,0.26 3.802,0.49 0.333,0.229 10 false E75 4.583,0.938 5.177,1.135 0.594,0.198 10 false CANH*b 4.531,0.719 5.104,0.917 0.573,0.198 10 false CANH*c 4.469,0.51 5.052,0.719 0.583,0.208 10 false CANH*d 4.333,0.271 4.896,0.469 0.563,0.198 10 false CANH*e 4.594,1.167 5.167,1.396 0.573,0.229 10 false CANH*a 4.552,1.833 5.135,2.021 0.583,0.188 10 false CANL*a 4.49,2 5.073,2.229 0.583,0.229 10 false CANL*b 4.333,2.177 4.917,2.354 0.583,0.177 10 false CANL*c 4.208,2.365 4.792,2.563 0.583,0.198 10 false CANL*d 4.115,2.542 4.667,2.729 0.552,0.188 10 false CANL*e

Text in Illustration
*a
·

for No. 2 Junction Connector (w/ Network Gateway ECU)

·

for No. 6 Junction Connector (w/o Network Gateway ECU)


*b for DLC3
*c for Combination Meter Assembly (V Bus) *d for Main Body ECU (Cowl Side Junction Block LH) (V Bus)
*e for Master Cylinder Solenoid (Skid Control ECU) (w/o Network Gateway ECU) - -

No. 3 Junction Connector Wiring Color Connect to
E75-1 (CANH) W*1, *3
Y*2, *3
SB*4
·

No. 2 junction connector*1

·

No. 6 junction connector*2


E75-12 (CANL) B*1
L*2
E75-2 (CANH) G DLC3
E75-13 (CANL) B
E75-3 (CANH) V Combination meter assembly (V bus)
E75-14 (CANL) B
E75-4 (CANH) SB Main body ECU (cowl side junction block LH) (V bus)
E75-15 (CANL) B
E75-5 (CANH) V Master cylinder solenoid (skid control ECU)*2
E75-16 (CANL) L

*1: w/ Network Gateway ECU

*2: w/o Network Gateway ECU

*3: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*4: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



d.

NO. 4 JUNCTION CONNECTOR (w/ Network Gateway ECU)

U165000E02
4.552,1.229 4.438,1.229 4.438,1.229 4.229,1.469 false 4.083,1.469 4.396,1.01 4.396,1.01 4.521,1.01 false 3.948,1.469 4.313,0.792 4.313,0.792 4.469,0.792 false 4.5,1.906 4.375,1.906 4.375,1.906 4.208,1.719 false 4.073,1.719 4.281,2.073 4.281,2.073 4.417,2.073 false 3.948,1.719 4.156,2.25 4.156,2.25 4.281,2.25 false 3.813,1.469 4.292,0.583 4.292,0.583 4.417,0.583 false 3.813,1.719 4.01,2.438 4.01,2.438 4.146,2.438 false 3.479,0.26 3.813,0.5 0.333,0.24 10 false E71 4.563,0.948 5.156,1.167 0.594,0.219 10 false CANH*b 4.521,0.719 5.104,0.938 0.583,0.219 10 false CANH*c 4.469,0.51 5.042,0.688 0.573,0.177 10 false CANH*d 4.594,1.167 5.229,1.375 0.635,0.208 10 false CANH*a 4.552,1.823 5.125,2.01 0.573,0.188 10 false CANL*a 4.469,2.01 5.021,2.219 0.552,0.208 10 false CANL*b 4.344,2.188 4.896,2.385 0.552,0.198 10 false CANL*c 4.188,2.365 4.75,2.583 0.563,0.219 10 false CANL*d

Text in Illustration
*a for No. 5 Junction Connector *b for Network Gateway ECU (Movement Control Bus)
*c for 4WD Control ECU *d for Power Steering ECU Assembly (for 1VD-FTV with DPF)

No. 4 Junction Connector Wiring Color Connect to
E71-1 (CANH) W No. 5 junction connector
E71-12 (CANL) L
E71-2 (CANH) SB Network gateway ECU (Movement control bus)
E71-13 (CANL) L
E71-3 (CANH) P 4WD control ECU
E71-14 (CANL) L
E71-4 (CANH) LG Power steering ECU assembly*
E71-15 (CANL) L

*: for 1VD-FTV with DPF



e.

NO. 5 JUNCTION CONNECTOR (w/ Network Gateway ECU)

U165001E02
4.531,1.229 4.417,1.229 4.417,1.229 4.208,1.469 false 4.083,1.469 4.396,1.01 4.396,1.01 4.521,1.01 false 3.948,1.469 4.313,0.792 4.313,0.792 4.469,0.792 false 4.5,1.906 4.375,1.906 4.375,1.906 4.208,1.719 false 4.083,1.719 4.292,2.073 4.292,2.073 4.427,2.073 false 3.958,1.719 4.167,2.25 4.167,2.25 4.292,2.25 false 3.823,1.469 4.302,0.583 4.302,0.583 4.427,0.583 false 3.698,1.469 4.125,0.354 4.125,0.354 4.281,0.354 false 3.833,1.719 4.031,2.438 4.031,2.438 4.167,2.438 false 3.698,1.719 3.906,2.615 3.906,2.615 4.063,2.615 false 3.479,0.26 3.813,0.49 0.333,0.229 10 false E68 4.573,0.927 5.146,1.146 0.573,0.219 10 false CANH*b 4.542,0.719 5.146,0.917 0.604,0.198 10 false CANH*c 4.479,0.51 5.063,0.719 0.583,0.208 10 false CANH*d 4.313,0.271 4.896,0.469 0.583,0.198 10 false CANH*e 4.583,1.177 5.167,1.385 0.583,0.208 10 false CANH*a 4.542,1.813 5.125,2.01 0.583,0.198 10 false CANL*a 4.469,2 5.031,2.188 0.563,0.188 10 false CANL*b 4.333,2.177 4.906,2.375 0.573,0.198 10 false CANL*c 4.208,2.365 4.802,2.573 0.594,0.208 10 false CANL*d 4.104,2.531 4.656,2.719 0.552,0.188 10 false CANL*e

Text in Illustration
*a for No. 4 Junction Connector *b for No. 6 Junction Connector
*c for Yaw Rate Sensor Assembly (w/ Vehicle Stability Control System) *d for Distance Control ECU Assembly (w/ Dynamic Radar Cruise Control System)
*e for Seat Belt Control ECU (w/ Pre-crash Safety System) - -

No. 5 Junction Connector Wiring Color Connect to
E68-1 (CANH) W No. 4 junction connector
E68-12 (CANL) L
E68-2 (CANH) Y*4, SB*5 No. 6 junction connector
E68-13 (CANL) L
E68-3 (CANH) BR Yaw rate sensor assembly*1
E68-14 (CANL) L
E68-4 (CANH) SB Distance control ECU assembly*2
E68-15 (CANL) L
E68-5 (CANH) G Seat belt control ECU*3
E68-16 (CANL) L

*1: w/ Vehicle Stability Control System

*2: w/ Dynamic Radar Cruise Control System

*3: w/ Pre-crash Safety System

*4: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*5: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



f.

NO. 6 JUNCTION CONNECTOR

U165002E01
3.468,0.287 3.740,0.426 0.272,0.140 10 F73 2.284,0.443 2.836,0.583 0.552,0.140 10 CANH*b 2.227,0.674 2.779,0.813 0.552,0.140 10 CANH*c 2.422,0.212 2.974,0.352 0.552,0.140 10 CANH*a 3.473,1.466 2.946,0.737 2.946,0.737 2.788,0.737 false 3.473,1.727 3.147,2.145 3.147,2.145 3.014,2.145 false 3.611,1.466 2.975,0.508 2.975,0.508 2.844,0.508 false 3.74,1.466 3.145,0.278 3.145,0.278 2.987,0.278 false 3.611,1.727 3.333,2.366 3.333,2.366 3.202,2.366 false 3.74,1.727 3.533,2.585 3.533,2.585 3.374,2.585 false 2.832,2.512 3.384,2.652 0.552,0.140 10 CANL*a 2.649,2.294 3.201,2.434 0.552,0.140 10 CANL*b 2.46,2.08 3.011,2.220 0.552,0.140 10 CANL*c

Text in Illustration
*a
·

for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System)

·

for Parking Assist ECU (w/ Side Monitor System)


*b
·

for No. 7 Junction Connector (w/ Network Gateway ECU)

·

for No. 3 Junction Connector (w/o Network Gateway ECU)


*c
·

for No. 5 Junction Connector (w/ Network Gateway ECU)

·

for No. 2 Junction Connector (w/o Network Gateway ECU)


- -

No. 6 Junction Connector Wiring Color Connect to
F73-5 (CANH) V
·

Clearance warning ECU assembly*1

·

Parking assist ECU*2


F73-16 (CANL) L
F73-6 (CANH) Y*5, SB*6
·

No. 7 junction connector*3

·

No. 3 junction connector*4


F73-17 (CANL) L
F73-7 (CANH) Y*5, SB*6
·

No. 5 junction connector*3

·

No. 2 junction connector*4


F73-18 (CANL) L

*1: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System

*2: w/ Side Monitor System

*3: w/ Network Gateway ECU

*4: w/o Network Gateway ECU

*5: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*6: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



g.

NO. 7 JUNCTION CONNECTOR (w/ Network Gateway ECU)

U165003E02
4.542,1.229 4.427,1.229 4.427,1.229 4.219,1.469 false 4.083,1.469 4.396,1.01 4.396,1.01 4.521,1.01 false 3.938,1.469 4.302,0.792 4.302,0.792 4.458,0.792 false 4.5,1.917 4.375,1.917 4.375,1.917 4.208,1.729 false 4.073,1.729 4.281,2.083 4.281,2.083 4.417,2.083 false 3.958,1.729 4.167,2.26 4.167,2.26 4.292,2.26 false 3.813,1.469 4.292,0.583 4.292,0.583 4.417,0.583 false 3.688,1.469 4.115,0.354 4.115,0.354 4.271,0.354 false 3.823,1.729 4.021,2.448 4.021,2.448 4.156,2.448 false 3.708,1.729 3.917,2.625 3.917,2.625 4.073,2.625 false 3.479,0.26 3.813,0.479 0.333,0.219 10 false E74 4.552,0.938 5.115,1.135 0.563,0.198 10 false CANH*b 4.49,0.719 5.063,0.927 0.573,0.208 10 false CANH*c 4.458,0.5 5.031,0.677 0.573,0.177 10 false CANH*d 4.302,0.281 4.896,0.469 0.594,0.188 10 false CANH*e 4.583,1.156 5.146,1.354 0.563,0.198 10 false CANH*a 4.552,1.844 5.135,2.031 0.583,0.188 10 false CANL*a 4.458,2.021 5.042,2.208 0.583,0.188 10 false CANL*b 4.333,2.198 4.948,2.427 0.615,0.229 10 false CANL*c 4.188,2.375 4.802,2.563 0.615,0.188 10 false CANL*d 4.115,2.552 4.719,2.719 0.604,0.167 10 false CANL*e

Text in Illustration
*a for No. 1 CAN Junction Connector *b for No. 6 Junction Connector
*c for Steering Control ECU (w/ Variable Gear Ratio Steering System) *d for Steering Angle Sensor (w/ Vehicle Stability Control System)
*e for Master Cylinder Solenoid (Skid Control ECU) - -

No. 7 Junction Connector Wiring Color Connect to
E74-1 (CANH) W No. 1 CAN junction connector
E74-12 (CANL) L
E74-2 (CANH) Y*3, SB*4 No. 6 junction connector
E74-13 (CANL) L
E74-3 (CANH) LG Steering control ECU*1
E74-14 (CANL) L
E74-4 (CANH) GR Steering angle sensor*2
E74-15 (CANL) L
E74-5 (CANH) V Master cylinder solenoid (skid control ECU)
E74-16 (CANL) L

*1: w/ Variable Gear Ratio Steering System

*2: w/ Vehicle Stability Control System

*3: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*4: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC



h.

NO. 8 JUNCTION CONNECTOR

U165004E01
3.468,0.287 3.740,0.426 0.272,0.140 10 E76 4.575,0.94 5.127,1.080 0.552,0.140 10 CANH*b 4.521,0.73 5.073,0.869 0.552,0.140 10 CANH*c 4.449,0.524 5.001,0.664 0.552,0.140 10 CANH*d 4.297,0.284 4.849,0.423 0.552,0.140 10 CANH*e 2.443,0.284 2.995,0.423 0.552,0.140 10 CANH*f 4.573,1.176 5.125,1.315 0.552,0.140 10 CANH*a 4.552,1.229 4.428,1.229 4.428,1.229 4.225,1.466 false 4.101,1.466 4.41,1.012 4.41,1.012 4.54,1.012 false 3.973,1.466 4.335,0.795 4.335,0.795 4.494,0.795 false 4.515,1.918 4.391,1.918 4.391,1.918 4.225,1.727 false 4.101,1.727 4.313,2.085 4.313,2.085 4.444,2.085 false 3.973,1.727 4.18,2.264 4.18,2.264 4.313,2.264 false 3.835,1.466 4.306,0.58 4.306,0.58 4.437,0.58 false 3.835,1.727 4.032,2.447 4.032,2.447 4.163,2.447 false 3.593,1.466 3.17,0.351 3.17,0.351 3.012,0.351 false 3.593,1.727 3.386,2.623 3.386,2.623 3.227,2.623 false 3.706,1.466 4.128,0.351 4.128,0.351 4.287,0.351 false 3.706,1.727 3.913,2.623 3.913,2.623 4.072,2.623 false 4.538,1.857 5.090,1.997 0.552,0.140 10 CANL*a 4.468,2.023 5.019,2.163 0.552,0.140 10 CANL*b 4.337,2.207 4.889,2.346 0.552,0.140 10 CANL*c 4.174,2.384 4.725,2.524 0.552,0.140 10 CANL*d 4.087,2.561 4.639,2.701 0.552,0.140 10 CANL*e 2.7,2.561 3.252,2.701 0.552,0.140 10 CANL*f

Text in Illustration
*a for No. 2 CAN Junction Connector *b for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*c for Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System) *d for Position Control ECU and Switch (w/ Seat Memory)
*e for Outer Mirror Control ECU Assembly (w/ Seat Memory) *f for Main Body ECU (Cowl Side Junction Block LH) (MS Bus)

No. 8 Junction Connector Wiring Color Connect to
E76-1 (CANH) W No. 2 CAN junction connector
E76-12 (CANL) R
E76-2 (CANH) LG Certification ECU (smart key ECU assembly)*1
E76-13 (CANL) R
E76-3 (CANH) P Multiplex tilt and telescopic ECU*2
E76-14 (CANL) R
E76-4 (CANH) V Position control ECU and switch*3
E76-15 (CANL) R
E76-5 (CANH) BR Outer mirror control ECU assembly*3
E76-16 (CANL) R
E76-6 (CANH) GR Main body ECU (cowl side junction block LH) (MS bus)
E76-17 (CANL) R

*1: w/ Entry and Start System

*2: w/ Power Tilt and Power Telescopic Steering Column System

*3: w/ Seat Memory



i.

NO. 9 JUNCTION CONNECTOR

U165005E02
4.521,1.229 4.406,1.229 4.406,1.229 4.198,1.469 false 4.083,1.469 4.396,1.01 4.396,1.01 4.521,1.01 false 3.948,1.469 4.313,0.792 4.313,0.792 4.469,0.792 false 4.51,1.917 4.385,1.917 4.385,1.917 4.219,1.729 false 4.094,1.729 4.302,2.083 4.302,2.083 4.438,2.083 false 3.958,1.729 4.167,2.26 4.167,2.26 4.292,2.26 false 3.823,1.469 4.302,0.583 4.302,0.583 4.427,0.583 false 3.823,1.729 4.021,2.448 4.021,2.448 4.156,2.448 false 3.458,0.26 3.802,0.49 0.344,0.229 10 false E73 4.552,0.938 5.125,1.115 0.573,0.177 10 false CANH*b 4.51,0.708 5.083,0.906 0.573,0.198 10 false CANH*c 4.458,0.5 5.052,0.688 0.594,0.188 10 false CANH*d 4.552,1.156 5.115,1.385 0.563,0.229 10 false CANH*a 4.552,1.844 5.104,2.031 0.552,0.188 10 false CANL*a 4.49,2.021 5.063,2.188 0.573,0.167 10 false CANL*b 4.333,2.198 4.896,2.396 0.563,0.198 10 false CANL*c 4.188,2.375 4.76,2.594 0.573,0.219 10 false CANL*d

Text in Illustration
*a for No. 10 Junction Connector *b for No. 2 CAN Junction Connector
*c for Accessory Bus Buffer *d for Windshield Wiper ECU (w/ Rain Sensor)

No. 9 Junction Connector Wiring Color Connect to
E73-1 (CANH) W No. 10 junction connector
E73-12 (CANL) R
E73-2 (CANH) Y No. 2 CAN junction connector
E73-13 (CANL) R
E73-3 (CANH) V Accessory bus buffer
E73-14 (CANL) R
E73-4 (CANH) LG Windshield wiper ECU*
E73-15 (CANL) R

*: w/ Rain Sensor



j.

NO. 10 JUNCTION CONNECTOR

U165006E02
4.521,1.229 4.406,1.229 4.406,1.229 4.198,1.469 false 3.938,1.469 4.302,0.969 4.302,0.969 4.458,0.969 false 4.5,1.917 4.375,1.917 4.375,1.917 4.208,1.729 false 3.948,1.729 4.156,2.26 4.156,2.26 4.281,2.26 false 3.458,0.26 3.802,0.469 0.344,0.208 10 false E70 4.51,0.896 5.104,1.094 0.594,0.198 10 false CANH*b 4.563,1.156 5.125,1.385 0.563,0.229 10 false CANH*a 4.552,1.844 5.135,2.052 0.583,0.208 10 false CANL*a 4.323,2.188 4.875,2.406 0.552,0.219 10 false CANL*b

Text in Illustration
*a for No. 9 Junction Connector *b for Combination Meter Assembly (MS Bus)

No. 10 Junction Connector Wiring Color Connect to
E70-1 (CANH) W No. 9 junction connector
E70-12 (CANL) R
E70-3 (CANH) LG Combination meter assembly (MS bus)
E70-14 (CANL) R


k.

NO. 1 CAN JUNCTION CONNECTOR (w/ Network Gateway ECU)

E349318E01
0.333,0.5 0.75,0.792 0.417,0.292 0.333,1.292 0.75,1.583 0.417,0.292 0.333,2 0.75,2.292 0.417,0.292 0.75,1.448 0.917,1.448 0.917,1.448 1.49,1.229 false 0.76,2.135 0.927,2.135 0.927,2.135 1.49,1.604 false 0.76,0.625 0.917,0.625 0.917,0.625 1.365,0.792 false 0.427,0.563 0.865,0.792 0.438,0.229 10 false K28 0.438,1.354 0.875,1.583 0.438,0.229 10 false K29 0.438,2.063 0.875,2.292 0.438,0.229 10 false K39

Junction Connector A Side Wiring Color (CANH Side) Wiring Color (CANL Side)
Ground terminal (K28) - W-B
No. 7 junction connector (K29) W L
Suspension control ECU (K39)* V L

*: w/ Active Height Control Suspension



l.

NO. 2 CAN JUNCTION CONNECTOR

E349319E01
6.25,0.5 6.667,0.781 0.417,0.281 6.25,0.875 6.667,1.156 0.417,0.281 6.25,1.542 6.667,1.823 0.417,0.281 6.25,1.906 6.667,2.188 0.417,0.281 6.25,2.271 6.667,2.552 0.417,0.281 5.469,0.885 6.083,0.635 6.083,0.635 6.25,0.635 false 5.458,1.26 6.073,1.01 6.073,1.01 6.24,1.01 false 5.458,1.646 6.094,1.708 6.094,1.708 6.24,1.708 false 5.469,2.021 6.083,2.063 6.083,2.063 6.24,2.063 false 5.469,2.417 6.25,2.417 false 6.354,0.563 6.802,0.781 0.448,0.219 10 false L29 6.344,0.938 6.792,1.156 0.448,0.219 10 false L30 6.344,1.604 6.792,1.823 0.448,0.219 10 false L54 6.354,1.969 6.802,2.188 0.448,0.219 10 false L58 6.354,2.333 6.802,2.552 0.448,0.219 10 false L57

Junction Connector B Side Wiring Color (CANH Side) Wiring Color (CANL Side)
No. 8 junction connector (L29) LG GR
No. 9 junction connector (L30) Y R
Power back door unit assembly (power back door ECU) (L54)*1 V R
No. 2 main body ECU (L57)*1 LG R
Tire pressure warning ECU and receiver (L58)*2 G R

*1: w/ Power Back Door System

*2: w/ Tire Pressure Warning System




TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (CAN JUNCTION CONNECTOR)


C135249

Terminal No. Symbol
1 CANH
2 CANL


CHECK DLC3


a.
U165237E02
1.594,0.885 1.396,0.396 1.396,0.396 1.271,0.396 false 1.948,0.885 2.146,0.396 2.146,0.396 2.271,0.396 false 2.323,1.469 2.469,1.896 2.469,1.896 2.604,1.896 false 1.948,1.469 1.802,1.896 1.802,1.896 1.667,1.896 false 2.323,0.323 2.792,0.51 0.469,0.188 10 false CANH 1.021,0.313 1.354,0.521 0.333,0.208 10 false CG 1.271,1.802 1.677,1.99 0.406,0.188 10 false CANL 2.646,1.813 3.052,2 0.406,0.188 10 false BAT 0.271,1.104 0.563,1.333 0.292,0.229 10 false E22

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

NOTICE:
·

After turning the Ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) G - B Ignition switch off 54 to 69 Ω
E22-6 (CANH) - E22-4 (CG) G - W-B Ignition switch off 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) B - W-B Ignition switch off 200 Ω or higher
E22-6 (CANH) - E22-16 (BAT) G - BE Ignition switch off 6 kΩ or higher
E22-14 (CANL) - E22-16 (BAT) B - BE Ignition switch off 6 kΩ or higher



CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)


U164689E02
2.656,1.188 2.302,1.51 2.302,1.51 2.24,1.51 false 2.885,1.208 3.01,1.677 3.01,1.677 3.063,1.677 false 3.896,1.24 4.052,1.521 4.052,1.521 4.115,1.521 false 3.875,1.063 4.135,0.448 4.135,0.448 4.198,0.448 false 4.146,1.448 4.563,1.615 0.417,0.167 10 false CANH 1.833,1.448 2.25,1.615 0.417,0.167 10 false GND1 4.24,0.375 4.646,0.542 0.406,0.167 10 false CANL 3.333,0.24 3.635,0.406 0.302,0.167 10 false A24 3.104,1.583 3.521,1.75 0.417,0.167 10 false +BM1

a.

Disconnect the A24 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A24-11 (CANH) - A24-25 (CANL) V - L Ignition switch off 54 to 69 Ω
A24-11 (CANH) - A24-1 (GND1) V - W-B Ignition switch off 200 Ω or higher
A24-25 (CANL) - A24-1 (GND1) L - W-B Ignition switch off 200 Ω or higher
A24-11 (CANH) - A24-2 (+BM1) V - B Ignition switch off 6 kΩ or higher
A24-25 (CANL) - A24-2 (+BM1) L - B Ignition switch off 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Rear Air Conditioning System)


U164512E02
4.625,1.5 4.75,0.854 4.75,0.854 4.802,0.854 false 4.74,1.5 4.927,1.031 4.927,1.031 4.979,1.031 false 3.333,1.5 3.063,1.042 3.063,1.042 3.021,1.042 false 4.042,1.5 3.969,1.042 3.969,1.042 3.917,1.042 false 3.51,0.573 3.792,0.75 0.281,0.177 10 false E36 4.469,0.573 4.844,0.813 0.375,0.24 10 false E35 4.833,0.771 5.271,0.979 0.438,0.208 10 false CANL 5.01,0.948 5.458,1.146 0.448,0.198 10 false CANH 2.708,0.948 3,1.167 0.292,0.219 10 false +B1 3.583,0.969 3.938,1.198 0.354,0.229 10 false GND

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier.


Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E35-3 (CANH) - E35-4 (CANL) G - B Ignition switch off 54 to 69 Ω
E35-3 (CANH) - E36-1 (GND) G - W-B Ignition switch off 200 Ω or higher
E35-4 (CANL) - E36-1 (GND) B - W-B Ignition switch off 200 Ω or higher
E35-3 (CANH) - E36-6 (+B1) G - R Ignition switch off 6 kΩ or higher
E35-4 (CANL) - E36-6 (+B1) B - R Ignition switch off 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/o Rear Air Conditioning System)


U164549E02
3.854,1.375 4.063,0.875 4.063,0.875 4.115,0.875 false 3.74,1.375 3.479,0.615 3.479,0.615 3.427,0.615 false 4.958,1.552 5.094,1.958 5.094,1.958 5.135,1.958 false 3.521,1.365 3.125,0.875 3.125,0.875 3.073,0.875 false 3.771,0.521 4.083,0.729 0.313,0.208 10 false E81 4.156,0.792 4.583,0.958 0.427,0.167 10 false CANH 3.042,0.542 3.49,0.75 0.448,0.208 10 false CANL 5.177,1.885 5.51,2.083 0.333,0.198 10 false +B1 2.708,0.802 3.063,0.99 0.354,0.188 10 false GND

a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E81-11 (CANH) - E81-12 (CANL) G - B Ignition switch off 54 to 69 Ω
E81-11 (CANH) - E81-14 (GND) G - W-B Ignition switch off 200 Ω or higher
E81-12 (CANL) - E81-14 (GND) B - W-B Ignition switch off 200 Ω or higher
E81-11 (CANH) - E81-21 (+B1) G - R Ignition switch off 6 kΩ or higher
E81-12 (CANL) - E81-21 (+B1) B - R Ignition switch off 6 kΩ or higher



CHECK ECM


U164554E02
5.958,1.094 6.208,0.979 6.208,0.979 6.25,0.979 false 5.969,1.323 6.219,1.208 6.219,1.208 6.26,1.208 false 1.927,1.792 2,2.344 2,2.344 2.063,2.344 false 4.719,1.073 4.552,0.583 4.552,0.583 4.479,0.583 false 4.583,1.073 4.354,0.76 4.354,0.76 4.292,0.76 false 4.552,1.698 4.135,2.302 4.135,2.302 4.083,2.302 false 4.583,1.844 4.365,2.438 4.365,2.438 4.292,2.438 false 2.104,2.281 2.344,2.49 0.24,0.208 10 false E1 4.99,0.292 5.344,0.542 0.354,0.25 10 false A38 6.281,0.906 6.823,1.115 0.542,0.208 10 false BATT*A 6.302,1.135 6.854,1.385 0.552,0.25 10 false BATT*B 2.615,0.292 2.927,0.479 0.313,0.188 10 false C45 3.906,0.521 4.521,0.719 0.615,0.198 10 false CANH*A 3.75,0.698 4.365,0.906 0.615,0.208 10 false CANL*A 3.75,2.375 4.313,2.594 0.563,0.219 10 false CANL*B 3.51,2.219 4.135,2.458 0.625,0.24 10 false CANH*B

Text in Illustration
*A except 1VD-FTV *B for 1VD-FTV

a.

Disconnect the A38 and C45 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

for 1GR-FE
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-10 (CANH) - A38-11 (CANL) P - B Ignition switch off 108 to 132 Ω
A38-10 (CANH) - C45-81 (E1) P - BR Ignition switch off 200 Ω or higher
A38-11 (CANL) - C45-81 (E1) B - BR Ignition switch off 200 Ω or higher
A38-10 (CANH) - A38-1 (BATT) P - L Ignition switch off 6 kΩ or higher
A38-11 (CANL) - A38-1 (BATT) B - L Ignition switch off 6 kΩ or higher

for 1UR-FE
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-10 (CANH) - A38-11 (CANL) P - B Ignition switch off 108 to 132 Ω
A38-10 (CANH) - C45-81 (E1) P - BR Ignition switch off 200 Ω or higher
A38-11 (CANL) - C45-81 (E1) B - BR Ignition switch off 200 Ω or higher
A38-10 (CANH) - A38-1 (BATT) P - L Ignition switch off 6 kΩ or higher
A38-11 (CANL) - A38-1 (BATT) B - L Ignition switch off 6 kΩ or higher

for 3UR-FE
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-10 (CANH) - A38-11 (CANL) P - B Ignition switch off 108 to 132 Ω
A38-10 (CANH) - C45-81 (E1) P - W-B Ignition switch off 200 Ω or higher
A38-11 (CANL) - C45-81 (E1) B - W-B Ignition switch off 200 Ω or higher
A38-10 (CANH) - A38-1 (BATT) P - L Ignition switch off 6 kΩ or higher
A38-11 (CANL) - A38-1 (BATT) B - L Ignition switch off 6 kΩ or higher

for 1VD-FTV
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-41 (CANH) - A38-49 (CANL) P - B Ignition switch off 108 to 132 Ω
A38-41 (CANH) - C45-81 (E1) P - BR Ignition switch off 200 Ω or higher
A38-49 (CANL) - C45-81 (E1) B - BR Ignition switch off 200 Ω or higher
A38-41 (CANH) - A38-20 (BATT) P - L Ignition switch off 6 kΩ or higher
A38-49 (CANL) - A38-20 (BATT) B - L Ignition switch off 6 kΩ or higher



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U164695E01
2.239,2.818 2.472,2.989 0.233,0.171 10 2A 1.095,3.699 1.287,3.840 0.192,0.141 10 2A 3.028,3.658 3.220,3.799 0.192,0.141 10 2B 5.611,3.658 5.810,3.799 0.199,0.141 10 2C 1.969,2.084 2.181,2.256 0.212,0.171 10 2B 1.969,1.223 2.181,1.394 0.212,0.171 10 2C 4.945,1.688 5.157,1.859 0.212,0.171 10 2D 5.573,0.648 5.785,0.819 0.212,0.171 10 2E 2.918,1.074 3.137,1.245 0.219,0.171 10 E1 2.918,1.589 3.137,1.760 0.219,0.171 10 E2 2.918,2.163 3.137,2.334 0.219,0.171 10 E3 1.103,8.491 1.773,8.628 0.671,0.137 10 CANP*B 1.637,7.123 2.190,7.263 0.552,0.140 10 CANL*A 1.517,6.489 1.937,6.660 0.420,0.171 10 GND2 1.75,7.504 2.366,7.642 0.617,0.137 10 CANH*A 1.35,8.247 2.021,8.384 0.671,0.137 10 CANN*B 2.918,2.517 3.137,2.689 0.219,0.171 10 E4 0.408,4.634 0.793,4.773 0.386,0.139 10 ALTB 2.89,1.13 2.801,1.13 2.801,1.13 2.387,1.386 false 5.53,0.718 5.442,0.718 5.442,0.718 5.028,0.973 false 2.89,1.641 2.817,1.641 2.817,1.641 2.41,1.796 false 2.89,2.601 2.801,2.601 2.801,2.601 2.387,2.345 false 2.89,2.228 2.817,2.228 2.817,2.228 2.41,2.128 false 1.329,7.8 1.568,7.194 1.568,7.194 1.618,7.194 false 1.447,7.804 1.661,7.562 1.661,7.562 1.725,7.562 false 1.003,8.016 1.259,8.305 1.259,8.305 1.326,8.305 false 0.886,8.02 0.999,8.554 0.999,8.554 1.079,8.554 false 1.121,4.443 0.92,4.701 0.92,4.701 0.788,4.701 false 1.149,6.106 1.309,6.548 1.309,6.548 1.474,6.548 false 4.421,5.241 4.614,5.382 0.192,0.141 10 2E 1.659,5.241 1.854,5.382 0.196,0.141 10 2D 6.124,5.083 6.316,5.224 0.192,0.141 10 E4 1.059,7.013 1.251,7.154 0.192,0.141 10 E3 3.556,7.013 3.748,7.154 0.192,0.141 10 E2 6.02,7.013 6.213,7.154 0.192,0.141 10 E1

Text in Illustration
*A V Bus *B MS Bus

a.

Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E3-5 (CANH) - E3-6 (CANL) SB - B Ignition switch off 54 to 69 Ω
E3-5 (CANH) - 2D-62 (GND2) SB - W-B Ignition switch off 200 Ω or higher
E3-6 (CANL) - 2D-62 (GND2) B - W-B Ignition switch off 200 Ω or higher
E3-5 (CANH) - 2A-1 (ALTB) SB - B Ignition switch off 6 kΩ or higher
E3-6 (CANL) - 2A-1 (ALTB) B - B Ignition switch off 6 kΩ or higher

for MS Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E3-16 (CANP) - E3-15 (CANN) GR - R Ignition switch off 108 to 132 Ω
E3-16 (CANP) - 2D-62 (GND2) GR - W-B Ignition switch off 200 Ω or higher
E3-15 (CANN) - 2D-62 (GND2) R - W-B Ignition switch off 200 Ω or higher
E3-16 (CANP) - 2A-1 (ALTB) GR - B Ignition switch off 6 kΩ or higher
E3-15 (CANN) - 2A-1 (ALTB) R - B Ignition switch off 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U165832E01
4.884,0.353 5.078,0.490 0.194,0.138 10 E7 6.123,0.656 6.743,0.803 0.619,0.147 10 MPX+*B 6.006,0.411 6.601,0.558 0.595,0.147 10 MPX-*B 3.515,1.595 4.069,1.742 0.554,0.147 10 CANL*A 4.851,1.595 5.456,1.742 0.605,0.147 10 CANH*A 3.558,0.622 3.765,0.769 0.207,0.147 10 EP 5.927,1.594 6.041,1.741 0.114,0.147 10 B 4.435,1.313 4.196,1.662 false 4.435,1.313 4.196,1.662 false 4.435,1.313 4.196,1.662 4.196,1.662 4.057,1.662 false 4.557,1.317 4.709,1.662 false 4.557,1.317 4.709,1.662 false 4.557,1.317 4.709,1.662 4.709,1.662 4.835,1.662 false 5.556,1.316 5.79,1.665 5.79,1.665 5.919,1.665 false 4.195,1.082 3.886,0.701 3.886,0.701 3.771,0.701 false 5.66,1.081 5.844,0.482 5.844,0.482 5.99,0.482 false 5.794,1.089 5.982,0.725 5.982,0.725 6.104,0.725 false

Text in Illustration
*A V Bus *B MS Bus

a.

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

for V Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E7-25 (CANH) - E7-26 (CANL) V - B Ignition switch off 108 to 132 Ω
E7-25 (CANH) - E7-14 (EP) V - W-B Ignition switch off 200 Ω or higher
E7-26 (CANL) - E7-14 (EP) B - W-B Ignition switch off 200 Ω or higher
E7-25 (CANH) - E7-17 (B) V - R Ignition switch off 6 kΩ or higher
E7-26 (CANL) - E7-17 (B) B - R Ignition switch off 6 kΩ or higher

for MS Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E7-1 (MPX+) - E7-2 (MPX-) LG - R Ignition switch off 108 to 132 Ω
E7-1 (MPX+) - E7-14 (EP) LG - W-B Ignition switch off 200 Ω or higher
E7-2 (MPX-) - E7-14 (EP) R - W-B Ignition switch off 200 Ω or higher
E7-1 (MPX+) - E7-17 (B) LG - R Ignition switch off 6 kΩ or higher
E7-2 (MPX-) - E7-17 (B) R - R Ignition switch off 6 kΩ or higher



CHECK CENTER AIRBAG SENSOR ASSEMBLY (w/ Airbag System)


U164532E02
2.5,1.458 2.635,0.885 2.635,0.885 2.688,0.885 false 6.25,1.76 6.458,2.104 6.458,2.104 6.5,2.104 false 2.615,1.781 2.74,2.135 2.74,2.135 2.802,2.135 false 2.25,1.771 2.135,2.125 2.135,2.125 2.073,2.125 false 2.167,0.552 2.438,0.76 0.271,0.208 10 false E47 5.604,0.552 5.875,0.76 0.271,0.208 10 false E22 2.729,0.802 3.177,0.99 0.448,0.188 10 false CANH 2.854,2.052 3.292,2.25 0.438,0.198 10 false CANL 1.865,2.052 2.073,2.229 0.208,0.177 10 false E1 6.552,2.021 6.917,2.26 0.365,0.24 10 false BAT

a.

Disconnect the E47 center airbag sensor assembly connector (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E47-13 (CANH) - E47-22 (CANL) GR - B Ignition switch off 54 to 69 Ω
E47-13 (CANH) - E47-25 (E1) GR - W-B Ignition switch off 200 Ω or higher
E47-22 (CANL) - E47-25 (E1) B - W-B Ignition switch off 200 Ω or higher
E47-13 (CANH) - E22-16 (BAT) GR - BE Ignition switch off 6 kΩ or higher
E47-22 (CANL) - E22-16 (BAT) B - BE Ignition switch off 6 kΩ or higher



CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System)


U166251E01
2.483,1.562 2.747,1.699 0.264,0.138 10 F77 1.495,1.464 1.908,1.606 0.413,0.142 10 GND1 0.973,1.634 1.260,1.773 0.287,0.139 10 +B1 1.627,2.082 1.392,1.69 1.392,1.69 1.262,1.69 false 3.609,2.082 3.816,1.84 3.816,1.84 3.945,1.84 false 2.282,2.074 2.046,1.533 2.046,1.533 1.916,1.533 false 3.516,2.074 3.581,1.655 3.581,1.655 3.711,1.655 false 3.968,1.784 4.429,1.927 0.461,0.142 10 CANH 3.723,1.588 4.184,1.731 0.461,0.142 10 CANL

a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F77-1 (CANH) - F77-2 (CANL) P - B Ignition switch off 54 to 69 Ω
F77-1 (CANH) - F77-12 (GND1) P - W-B Ignition switch off 200 Ω or higher
F77-2 (CANL) - F77-12 (GND1) B - W-B Ignition switch off 200 Ω or higher
F77-1 (CANH) - F77-17 (+B1) P - R Ignition switch off 6 kΩ or higher
F77-2 (CANL) - F77-17 (+B1) B - R Ignition switch off 6 kΩ or higher



CHECK STEERING ANGLE SENSOR (w/ Vehicle Stability Control System)


U164599E02
1.615,1.75 1.479,2.073 1.479,2.073 1.396,2.073 false 1.75,1.781 1.792,2.094 1.792,2.094 1.865,2.094 false 2.677,1.75 2.854,2.083 2.854,2.083 2.917,2.083 false 5.604,1.844 5.75,2.125 5.75,2.125 5.813,2.125 false 2.146,0.948 2.49,1.177 0.344,0.229 10 false E11 0.948,1.99 1.375,2.198 0.427,0.208 10 false CANH 1.917,2 2.333,2.25 0.417,0.25 10 false CANL 2.958,2.01 3.344,2.219 0.385,0.208 10 false ESS 5.021,0.948 5.354,1.146 0.333,0.198 10 false E22 5.865,2.042 6.208,2.26 0.344,0.219 10 false BAT

a.

Disconnect the E11 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E11-10 (CANH) - E11-9 (CANL) GR - L Ignition switch off 54 to 69 Ω
E11-10 (CANH) - E11-2 (ESS) GR - W-B Ignition switch off 200 Ω or higher
E11-9 (CANL) - E11-2 (ESS) L - W-B Ignition switch off 200 Ω or higher
E11-10 (CANH) - E22-16 (BAT) GR - BE Ignition switch off 6 kΩ or higher
E11-9 (CANL) - E22-16 (BAT) L - BE Ignition switch off 6 kΩ or higher



CHECK YAW RATE SENSOR ASSEMBLY (w/ Vehicle Stability Control System)


U164533E02
2.313,1.385 2.375,2.188 2.375,2.188 2.427,2.188 false 2.24,1.385 1.979,2.188 1.979,2.188 1.906,2.188 false 2.417,1.365 2.885,2.188 2.885,2.188 2.938,2.188 false 5.625,1.833 5.813,2.156 5.813,2.156 5.865,2.156 false 2.063,0.802 2.406,1.031 0.344,0.229 10 false E50 4.99,0.813 5.344,1.01 0.354,0.198 10 false E22 2.458,2.094 2.875,2.281 0.417,0.188 10 false CANL 1.469,2.094 1.948,2.333 0.479,0.24 10 false CANH 2.99,2.104 3.354,2.302 0.365,0.198 10 false GND 5.896,2.063 6.26,2.292 0.365,0.229 10 false BAT

a.

Disconnect the E50 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E50-3 (CANH) - E50-2 (CANL) BR - L Ignition switch off 54 to 69 Ω
E50-3 (CANH) - E50-1 (GND) BR - W-B Ignition switch off 200 Ω or higher
E50-2 (CANL) - E50-1 (GND) L - W-B Ignition switch off 200 Ω or higher
E50-3 (CANH) - E22-16 (BAT) BR - BE Ignition switch off 6 kΩ or higher
E50-2 (CANL) - E22-16 (BAT) L - BE Ignition switch off 6 kΩ or higher



CHECK SEAT BELT CONTROL ECU (w/ Pre-crash Safety System)


U164514E02
3.198,1.542 3.417,2.354 3.417,2.354 3.479,2.354 false 2.958,1.552 2.74,2.365 2.74,2.365 2.667,2.365 false 4.5,1.542 4.656,2.229 4.656,2.229 4.708,2.229 false 4.406,1.542 4.229,2.229 4.229,2.229 4.167,2.229 false 3.021,0.729 3.385,0.948 0.365,0.219 10 false E41 4.229,0.729 4.552,0.927 0.323,0.198 10 false E42 2.208,2.281 2.688,2.479 0.479,0.198 10 false PGND 3.521,2.26 3.792,2.479 0.271,0.219 10 false +B 3.771,2.146 4.177,2.354 0.406,0.208 10 false CANL 4.76,2.156 5.26,2.344 0.5,0.188 10 false CANH

a.

Disconnect the E41 and E42 seat belt control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E42-1 (CANH) - E42-2 (CANL) G - L Ignition switch off 54 to 69 Ω
E42-1 (CANH) - E41-8 (PGND) G - W-B Ignition switch off 200 Ω or higher
E42-2 (CANL) - E41-8 (PGND) L - W-B Ignition switch off 200 Ω or higher
E42-1 (CANH) - E41-7 (+B) G - R Ignition switch off 6 kΩ or higher
E42-2 (CANL) - E41-7 (+B) L - R Ignition switch off 6 kΩ or higher



CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System)


U164534E02
3.094,1.24 3.271,0.906 3.271,0.906 3.323,0.906 false 2.729,1.24 2.865,0.708 2.865,0.708 2.917,0.708 false 2.208,1.615 2.073,1.958 2.073,1.958 2.031,1.958 false 6.146,1.719 6.375,1.948 6.375,1.948 6.427,1.948 false 1.979,0.646 2.313,0.865 0.333,0.219 10 false F12 5.417,0.635 5.771,0.875 0.354,0.24 10 false E22 3.365,0.833 3.823,1.01 0.458,0.177 10 false CANH 2.969,0.625 3.365,0.792 0.396,0.167 10 false CANL 1.625,1.875 2.063,2.094 0.438,0.219 10 false GND1 6.479,1.865 6.813,2.083 0.333,0.219 10 false BAT

a.

Disconnect the F12 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F12-3 (CANH) - F12-5 (CANL) V - L Ignition switch off 54 to 69 Ω
F12-3 (CANH) - F12-17 (GND1) V - W-B Ignition switch off 200 Ω or higher
F12-5 (CANL) - F12-17 (GND1) L - W-B Ignition switch off 200 Ω or higher
F12-3 (CANH) - E22-16 (BAT) V - BE Ignition switch off 6 kΩ or higher
F12-5 (CANL) - E22-16 (BAT) L - BE Ignition switch off 6 kΩ or higher



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Memory)


U163922E02
3.885,1.385 3.531,2.104 3.531,2.104 3.479,2.104 false 4,0.698 3.958,0.698 3.958,0.698 3.896,1.219 false 4.323,1.479 4.208,2.104 4.208,2.104 4.125,2.104 false 4.302,1.156 4.542,0.698 4.542,0.698 4.594,0.698 false 4.479,0.333 4.771,0.531 0.292,0.198 10 false I17 2.885,0.323 3.146,0.542 0.26,0.219 10 false I18 4.042,0.604 4.479,0.833 0.438,0.229 10 false CANH 3.802,2.031 4.177,2.25 0.375,0.219 10 false GND 4.635,0.604 4.813,0.802 0.177,0.198 10 false B 3.094,2.031 3.531,2.229 0.438,0.198 10 false CANL

a.

Disconnect the I17 and I18 outer mirror control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I18-1 (CANH) - I18-21 (CANL) BR - R Ignition switch off 54 to 69 Ω
I18-1 (CANH) - I17-9 (GND) BR - W-B Ignition switch off 200 Ω or higher
I18-21 (CANL) - I17-9 (GND) R - W-B Ignition switch off 200 Ω or higher
I18-1 (CANH) - I17-3 (B) BR - R Ignition switch off 6 kΩ or higher
I18-21 (CANL) - I17-3 (B) R - R Ignition switch off 6 kΩ or higher



CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)


U164535E02
3.563,1.771 3.406,2.146 3.406,2.146 3.333,2.146 false 4.031,1.781 4.188,2.146 4.188,2.146 4.24,2.146 false 4.01,1.469 4.26,0.958 4.26,0.958 4.323,0.958 false 3.531,1.49 3.177,0.948 3.177,0.948 3.083,0.948 false 3.448,0.635 3.76,0.896 0.313,0.26 10 false E27 2.896,2.063 3.375,2.281 0.479,0.219 10 false CANN 2.646,0.854 3.115,1.042 0.469,0.188 10 false CANP 4.302,2.063 4.74,2.281 0.438,0.219 10 false GND 4.375,0.865 4.625,1.104 0.25,0.24 10 false +B

a.

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E27-5 (CANP) - E27-14 (CANN) P - R Ignition switch off 54 to 69 Ω
E27-5 (CANP) - E27-11 (GND) P - W-B Ignition switch off 200 Ω or higher
E27-14 (CANN) - E27-11 (GND) R - W-B Ignition switch off 200 Ω or higher
E27-5 (CANP) - E27-2 (+B) P - L Ignition switch off 6 kΩ or higher
E27-14 (CANN) - E27-2 (+B) R - L Ignition switch off 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


U164536E02
2.615,1.5 2.51,1.885 2.51,1.885 2.438,1.885 false 3.813,1.302 3.948,1.01 3.948,1.01 4,1.01 false 1.188,1.302 1.031,0.99 1.031,0.99 0.948,0.99 false 2.75,1.479 2.885,1.875 2.885,1.875 2.948,1.875 false 2.333,0.792 2.667,1.031 0.333,0.24 10 false E29 2.021,1.802 2.49,2.021 0.469,0.219 10 false CANL 4.052,0.927 4.365,1.073 0.313,0.146 10 false +B 0.802,0.917 0.969,1.156 0.167,0.24 10 false E 3,1.781 3.469,2.021 0.469,0.24 10 false CANH

a.

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E29-27 (CANH) - E29-28 (CANL) LG - R Ignition switch off 54 to 69 Ω
E29-27 (CANH) - E29-17 (E) LG - W-B Ignition switch off 200 Ω or higher
E29-28 (CANL) - E29-17 (E) R - W-B Ignition switch off 200 Ω or higher
E29-27 (CANH) - E29-1 (+B) LG - B Ignition switch off 6 kΩ or higher
E29-28 (CANL) - E29-1 (+B) R - B Ignition switch off 6 kΩ or higher



CHECK POSITION CONTROL ECU AND SWITCH (w/ Seat Memory)


U164552E02
3.5,1.417 2.844,2.083 2.844,2.083 2.76,2.083 false 3.542,1.625 3.396,2.083 3.396,2.083 3.333,2.083 false 4.333,1.635 4.688,1.865 4.688,1.865 4.76,1.865 false 4.333,1.51 4.76,1.51 false 3.083,2 3.292,2.188 0.208,0.188 10 false +B 2.417,2 2.771,2.188 0.354,0.188 10 false GND 3,0.563 3.292,0.802 0.292,0.24 10 false c14 4.052,0.563 4.354,0.802 0.302,0.24 10 false c15 4.802,1.771 5.323,1.958 0.521,0.188 10 false MPX1 4.792,1.427 5.313,1.615 0.521,0.188 10 false MPX2

a.

Disconnect the c14 and c15 position control ECU and switch connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
c15-5 (MPX1) - c15-1 (MPX2) V - R Ignition switch off 54 to 69 Ω
c15-5 (MPX1) - c14-1 (GND) V - W-B Ignition switch off 200 Ω or higher
c15-1 (MPX2) - c14-1 (GND) R - W-B Ignition switch off 200 Ω or higher
c15-5 (MPX1) - c14-5 (+B) V - L Ignition switch off 6 kΩ or higher
c15-1 (MPX2) - c14-5 (+B) R - L Ignition switch off 6 kΩ or higher



CHECK 4WD CONTROL ECU


U164551E02
0.906,1.375 0.677,1.729 0.677,1.729 0.604,1.729 false 0.823,1.344 0.615,1.427 0.615,1.427 0.563,1.427 false 2.521,1.375 2.313,1.865 2.313,1.865 2.25,1.865 false 5.802,1.625 5.99,1.823 5.99,1.823 6.042,1.823 false 1.917,1.781 2.26,1.979 0.344,0.198 10 false GND 2.677,0.854 2.99,1.063 0.313,0.208 10 false A28 0.198,1.635 0.615,1.823 0.417,0.188 10 false CAN+ 0.188,1.333 0.563,1.521 0.375,0.188 10 false CAN- 1.427,0.854 1.781,1.031 0.354,0.177 10 false A27 5.146,0.604 5.458,0.813 0.313,0.208 10 false E22 6.115,1.729 6.469,1.917 0.354,0.188 10 false BAT

a.

Disconnect the A27 and A28 4WD control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A27-19 (CAN+) - A27-20 (CAN-) P - L Ignition switch off 54 to 69 Ω
A27-19 (CAN+) - A28-4 (GND) P - W Ignition switch off 200 Ω or higher
A27-20 (CAN-) - A28-4 (GND) L - W Ignition switch off 200 Ω or higher
A27-19 (CAN+) - E22-16 (BAT) P - BE Ignition switch off 6 kΩ or higher
A27-20 (CAN-) - E22-16 (BAT) L - BE Ignition switch off 6 kΩ or higher



CHECK NETWORK GATEWAY ECU (w/ Network Gateway ECU)


U164687E01
3.437,0.245 3.701,0.382 0.264,0.137 10 E31 4.345,0.325 4.737,0.498 0.391,0.173 10 BATT 3.905,1.573 4.420,1.712 0.515,0.140 10 CA2L*B 2.56,1.609 3.101,1.750 0.541,0.141 10 CA2H*B 1.9,1.521 2.420,1.663 0.520,0.142 10 CA1L*A 1.668,1.293 2.219,1.432 0.551,0.140 10 CA1H*A 2.502,0.357 2.843,0.530 0.341,0.173 10 GND 2.829,0.43 2.94,0.43 2.94,0.43 3.221,0.859 false 4.329,0.398 4.206,0.398 4.206,0.398 3.967,0.852 false 3.121,1.018 2.355,1.365 2.355,1.365 2.216,1.365 false 2.425,1.592 2.528,1.592 2.528,1.592 3.22,1.018 false 3.404,1.018 3.21,1.672 3.21,1.672 3.098,1.672 false 3.494,1.018 3.775,1.631 3.775,1.631 3.881,1.631 false

Text in Illustration
*A V Bus *B Movement Control Bus

a.

Disconnect the E31 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

for V Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E31-16 (CA1H) - E31-15 (CA1L) BR - B*1
BE - B*2
Ignition switch off 54 to 69 Ω
E31-16 (CA1H) - E31-4 (GND) BR - W-B*1
BE - W-B*2
Ignition switch off 200 Ω or higher
E31-15 (CA1L) - E31-4 (GND) B - W-B Ignition switch off 200 Ω or higher
E31-16 (CA1H) - E31-2 (BATT) BR - R*1
BE - R*2
Ignition switch off 6 kΩ or higher
E31-15 (CA1L) - E31-2 (BATT) B - R Ignition switch off 6 kΩ or higher

*1: Model code: GRJ200L-GNANKC, URJ202L-GNTEKC

*2: Model code except: GRJ200L-GNANKC, URJ202L-GNTEKC


for Movement Control Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E31-13 (CA2H) - E31-12 (CA2L) SB - L Ignition switch off 108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND) SB - W-B Ignition switch off 200 Ω or higher
E31-12 (CA2L) - E31-4 (GND) L - W-B Ignition switch off 200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT) SB - R Ignition switch off 6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT) L - R Ignition switch off 6 kΩ or higher



CHECK STEERING CONTROL ECU (w/ Variable Gear Ratio Steering System)


U164473E02
1.948,0.875 1.698,0.563 1.698,0.563 1.656,0.563 false 1.865,1.021 1.729,1.344 1.729,1.344 1.677,1.344 false 2.969,0.938 2.885,1.292 2.885,1.292 2.792,1.292 false 3.604,0.969 3.75,1.281 3.75,1.281 3.792,1.281 false 3.833,1.208 4.365,1.406 0.531,0.198 10 true PGND 2.469,1.208 2.802,1.427 0.333,0.219 10 true +BI 1.198,0.49 1.677,0.708 0.479,0.219 10 false CANH 1.208,1.25 1.656,1.458 0.448,0.208 10 true CANL 3.354,0.115 3.677,0.333 0.323,0.219 10 false E77 2.104,0.115 2.417,0.333 0.313,0.219 10 false E79

a.

Disconnect the E77 and E79 steering control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E79-9 (CANH) - E79-20 (CANL) LG - L Ignition switch off 54 to 69 Ω
E79-9 (CANH) - E77-7 (PGND) LG - W-B Ignition switch off 200 Ω or higher
E79-20 (CANL) - E77-7 (PGND) L - W-B Ignition switch off 200 Ω or higher
E79-9 (CANH) - E77-10 (+BI) LG - R Ignition switch off 6 kΩ or higher
E79-20 (CANL) - E77-10 (+BI) L - R Ignition switch off 6 kΩ or higher



CHECK SUSPENSION CONTROL ECU (w/ Active Height Control Suspension)


U164539E02
5.521,1.094 5.656,1.604 5.656,1.604 5.729,1.604 false 5.656,1.094 5.896,1.344 5.896,1.344 6,1.344 false 5.635,0.854 5.917,0.552 5.917,0.552 6.021,0.552 false 5.417,0.427 5.323,0.427 5.323,0.427 5.219,0.813 false 4.99,0.125 5.313,0.323 0.323,0.198 10 false K34 5.781,1.531 6.219,1.719 0.438,0.188 10 false CANL 6.073,0.469 6.51,0.656 0.438,0.188 10 false GND 5.458,0.344 5.896,0.531 0.438,0.188 10 false BAT2 6.042,1.26 6.479,1.448 0.438,0.188 10 false CANH

a.

Disconnect the K34 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
K34-7 (CANH) - K34-8 (CANL) V - L Ignition switch off 54 to 69 Ω
K34-7 (CANH) - K34-1 (GND) V - W-B Ignition switch off 200 Ω or higher
K34-8 (CANL) - K34-1 (GND) L - W-B Ignition switch off 200 Ω or higher
K34-7 (CANH) - K34-3 (BAT2) V - R Ignition switch off 6 kΩ or higher
K34-8 (CANL) - K34-3 (BAT2) L - R Ignition switch off 6 kΩ or higher



CHECK WINDSHIELD WIPER ECU (w/ Rain Sensor)


U164852E02
5.813,1.656 5.969,1.927 5.969,1.927 6.052,1.927 false 1.948,1.375 1.667,0.833 1.667,0.833 1.604,0.833 false 1.802,1.385 1.469,1.104 1.469,1.104 1.375,1.104 false 2.083,1.583 1.885,2.083 1.885,2.083 1.802,2.083 false 2,0.604 2.302,0.781 0.302,0.177 10 false E85 1.208,0.771 1.604,0.948 0.396,0.177 10 false CANL 1.677,2.01 1.813,2.188 0.135,0.177 10 false E 6.094,1.854 6.469,2.031 0.375,0.177 10 false BAT 0.958,1.042 1.375,1.219 0.417,0.177 10 false CANH 5.104,0.604 5.406,0.781 0.302,0.177 10 false E22

a.

Disconnect the E85 windshield wiper ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E85-6 (CANH) - E85-5 (CANL) LG - R Ignition switch off 54 to 69 Ω
E85-6 (CANH) - E85-10 (E) LG - W-B Ignition switch off 200 Ω or higher
E85-5 (CANL) - E85-10 (E) R - W-B Ignition switch off 200 Ω or higher
E85-6 (CANH) - E22-16 (BAT) LG - BE Ignition switch off 6 kΩ or higher
E85-5 (CANL) - E22-16 (BAT) R - BE Ignition switch off 6 kΩ or higher



CHECK PARKING ASSIST ECU (w/ Side Monitor System)


U166299E01
3.196,0.329 3.460,0.467 0.264,0.138 10 F76 4.856,0.329 5.120,0.467 0.264,0.138 10 F75 3.697,0.426 4.117,0.569 0.420,0.142 10 GND1 5.742,0.426 6.162,0.569 0.420,0.142 10 +B 3.189,1.491 3.625,1.630 0.436,0.139 10 CANL 1.883,1.491 2.319,1.630 0.436,0.139 10 CANH 2.718,1.082 2.445,1.551 2.445,1.551 2.315,1.551 false 2.763,1.082 3.037,1.551 3.037,1.551 3.166,1.551 false 5.392,0.965 5.599,0.492 5.599,0.492 5.728,0.492 false 4.457,0.965 4.25,0.492 4.25,0.492 4.121,0.492 false

a.

Disconnect the F75 and F76 parking assist ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-40 (CANH) - F76-39 (CANL) V - L Ignition switch off 54 to 69 Ω
F76-40 (CANH) - F75-4 (GND1) V - W-B Ignition switch off 200 Ω or higher
F76-39 (CANL) - F75-4 (GND1) L - W-B Ignition switch off 200 Ω or higher
F76-40 (CANH) - F75-1 (+B) V - L Ignition switch off 6 kΩ or higher
F76-39 (CANL) - F75-1 (+B) L - L Ignition switch off 6 kΩ or higher



CHECK DISTANCE CONTROL ECU ASSEMBLY (w/ Dynamic Radar Cruise Control System)


U165374E01
1.346,1.576 1.786,1.720 0.441,0.144 10 CANH 2.132,0.223 2.475,0.359 0.343,0.136 10 E108 5.183,0.223 5.447,0.359 0.264,0.136 10 E22 6.252,1.308 6.566,1.449 0.313,0.141 10 BAT 0.941,1.394 1.351,1.533 0.410,0.139 10 CANL 0.774,0.654 1.120,0.822 0.346,0.168 10 GND 1.759,1.639 1.901,1.639 1.901,1.639 2.123,0.984 false 1.337,1.464 1.491,1.464 1.491,1.464 2.002,0.99 false 1.106,0.722 1.248,0.722 1.248,0.722 1.461,0.922 false 6.231,1.383 6.075,1.383 6.075,1.383 5.834,1.204 false

a.

Disconnect the E108 distance control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E108-8 (CANH) - E108-9 (CANL) SB - L Ignition switch off 54 to 69 Ω
E108-8 (CANH) - E108-12 (GND) SB - BR Ignition switch off 200 Ω or higher
E108-9 (CANL) - E108-12 (GND) L - BR Ignition switch off 200 Ω or higher
E108-8 (CANH) - E22-16 (BAT) SB - BE Ignition switch off 6 kΩ or higher
E108-9 (CANL) - E22-16 (BAT) L - BE Ignition switch off 6 kΩ or higher



CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)


U164690E01
4.222,0.118 4.663,0.255 0.441,0.137 10 MPX1 2.558,0.232 2.990,0.400 0.432,0.168 10 ECUB 3.546,0.214 3.796,0.353 0.250,0.139 10 L52 4.332,0.378 4.742,0.515 0.410,0.137 10 MPX2 2.277,0.442 2.623,0.609 0.346,0.168 10 GND 2.978,0.302 3.102,0.302 3.102,0.302 3.192,0.858 false 2.609,0.509 2.698,0.509 2.698,0.509 3.023,0.877 false 4.195,0.185 4.083,0.185 4.083,0.185 3.697,0.937 false 4.304,0.441 4.208,0.441 4.208,0.441 3.814,0.935 false

a.

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L52-6 (MPX1) - L52-5 (MPX2) V - R Ignition switch off 54 to 69 Ω
L52-6 (MPX1) - L52-11 (GND) V - W-B Ignition switch off 200 Ω or higher
L52-5 (MPX2) - L52-11 (GND) R - W-B Ignition switch off 200 Ω or higher
L52-6 (MPX1) - L52-10 (ECUB) V - R Ignition switch off 6 kΩ or higher
L52-5 (MPX2) - L52-10 (ECUB) R - R Ignition switch off 6 kΩ or higher



CHECK TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)


U165423E02
6.344,1.781 6.5,2.052 6.5,2.052 6.667,2.052 false 3.177,1.844 3.333,2.302 3.333,2.302 3.5,2.302 false 3.458,1.854 3.625,2.125 3.625,2.125 3.781,2.125 false 3.167,1.375 3.323,1.01 3.323,1.01 3.49,1.01 false 2.354,0.781 2.667,0.969 0.313,0.188 10 false L60 5.802,0.854 6.094,1.042 0.292,0.188 10 false E22 6.74,1.979 7.052,2.125 0.313,0.146 10 false BAT 3.542,2.229 3.979,2.448 0.438,0.219 10 false CN1 3.854,2.042 4.208,2.26 0.354,0.219 10 false GN1 3.542,0.938 3.99,1.167 0.448,0.229 10 false CP1

a.

Disconnect the L60 tire pressure warning ECU and receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L63-3 (CP1) - L63-6 (CN1) W - B Ignition switch off 54 to 69 Ω
L63-3 (CP1) - L63-4 (GN1) W - G Ignition switch off 200 Ω or higher
L63-6 (CN1) - L63-4 (GN1) B - G Ignition switch off 200 Ω or higher
L63-3 (CP1) - E22-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
L63-6 (CN1) - E22-16 (BAT) B - BE Ignition switch off 6 kΩ or higher



CHECK NO. 2 MAIN BODY ECU (w/ Power Back Door System)


U164691E01
2.891,1.446 3.332,1.583 0.441,0.137 10 GND 2.36,0.231 2.792,0.399 0.432,0.168 10 MPX+ 3.546,0.213 3.796,0.352 0.250,0.139 10 L50 4.704,1.388 5.113,1.525 0.410,0.137 10 BECU 2.013,0.45 2.411,0.594 0.398,0.144 10 MPX- 2.78,0.301 2.903,0.301 2.903,0.301 2.994,0.857 false 2.411,0.508 2.5,0.508 2.5,0.508 2.825,0.875 false 3.233,1.513 3.346,1.513 3.346,1.513 3.576,0.992 false 4.675,1.451 4.579,1.451 4.579,1.451 4.345,1.147 false

a.

Disconnect the L50 No. 2 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L50-11 (MPX+) - L50-12 (MPX-) LG - R Ignition switch off 54 to 69 Ω
L50-11 (MPX+) - L50-7 (GND) LG - W-B Ignition switch off 200 Ω or higher
L50-12 (MPX-) - L50-7 (GND) R - W-B Ignition switch off 200 Ω or higher
L50-11 (MPX+) - L50-14 (BECU) LG - R Ignition switch off 6 kΩ or higher
L50-12 (MPX-) - L50-14 (BECU) R - R Ignition switch off 6 kΩ or higher



CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (w/ Dynamic Headlight Auto Leveling)


U164485E02
1.146,1.229 0.781,0.844 0.781,0.844 0.688,0.844 false 1.24,1.229 0.938,0.594 0.938,0.594 0.844,0.594 false 2.125,1.396 1.99,1.875 1.99,1.875 1.917,1.875 false 5.74,1.656 5.958,1.979 5.958,1.979 6.063,1.979 false 0.281,0.76 0.698,0.958 0.417,0.198 10 false MPX2 0.448,0.5 0.896,0.708 0.448,0.208 10 false MPX1 1.719,1.802 1.917,1.979 0.198,0.177 10 false E1 6.115,1.885 6.438,2.104 0.323,0.219 10 false BAT 1.875,0.667 2.229,0.865 0.354,0.198 10 false E101 5.083,0.656 5.385,0.854 0.302,0.198 10 false E22

a.

Disconnect the E101 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E101-12 (MPX1) - E101-13 (MPX2) LG - B Ignition switch off 54 to 69 Ω
E101-12 (MPX1) - E101-22 (E1) LG - W-B Ignition switch off 200 Ω or higher
E101-13 (MPX2) - E101-22 (E1) B - W-B Ignition switch off 200 Ω or higher
E101-12 (MPX1) - E22-16 (BAT) LG - BE Ignition switch off 6 kΩ or higher
E101-13 (MPX2) - E22-16 (BAT) B - BE Ignition switch off 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY (for 1VD-FTV with DPF)


U164995E01
2.569,1.462 3.013,1.686 0.444,0.225 10 CANH 2.362,1.625 2.836,1.762 0.473,0.137 10 CANL 1.401,1.447 1.744,1.591 0.343,0.144 10 GND 6.036,1.496 6.439,1.721 0.403,0.225 10 BAT 1.575,0.295 1.925,0.432 0.350,0.137 10 E102 5.086,0.293 5.359,0.435 0.272,0.143 10 E22 5.768,1.274 5.922,1.568 5.922,1.568 6.013,1.568 false 1.987,1.208 1.841,1.519 1.841,1.519 1.729,1.519 false 2.294,1.208 2.44,1.519 2.44,1.519 2.552,1.519 false 2.354,1.673 2.23,1.673 2.23,1.673 2.135,1.208 false

a.

Disconnect the E102 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E102-1 (CANH) - E102-2 (CANL) LG - L Ignition switch off 54 to 69 Ω
E102-1 (CANH) - E102-3 (GND) LG - W-B Ignition switch off 200 Ω or higher
E102-2 (CANL) - E102-3 (GND) L - W-B Ignition switch off 200 Ω or higher
E102-1 (CANH) - E22-16 (BAT) LG - BE Ignition switch off 6 kΩ or higher
E102-2 (CANL) - E22-16 (BAT) L - BE Ignition switch off 6 kΩ or higher



CHECK ACCESSORY BUS BUFFER


U166212E01
5.098,0.215 5.362,0.353 0.264,0.138 10 E22 2.161,0.215 2.353,0.353 0.191,0.138 10 E6 2.752,1.394 3.109,1.537 0.356,0.143 10 CAN- 1.424,1.394 1.815,1.537 0.391,0.143 10 CAN+ 4.59,0.417 4.815,0.559 0.225,0.142 10 CG 6.012,1.412 6.299,1.551 0.287,0.139 10 BAT 2.371,1.157 2.577,1.458 2.577,1.458 2.707,1.458 false 2.171,1.157 1.964,1.458 1.964,1.458 1.835,1.458 false 5.653,1.157 5.86,1.458 5.86,1.458 5.989,1.458 false 5.154,0.784 4.947,0.483 4.947,0.483 4.818,0.483 false

a.

Disconnect the E6 accessory bus buffer connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E6-1 (CAN+) - E6-2 (CAN-) V - R Ignition switch off 54 to 69 Ω
E6-1 (CAN+) - E22-4 (CG) V - W-B Ignition switch off 200 Ω or higher
E6-2 (CAN-) - E22-4 (CG) R - W-B Ignition switch off 200 Ω or higher
E6-1 (CAN+) - E22-16 (BAT) V - BE Ignition switch off 6 kΩ or higher
E6-2 (CAN-) - E22-16 (BAT) R - BE Ignition switch off 6 kΩ or higher