Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item DTC Detection Condition Trouble Area
Clearance Warning ECU Communication Stop Mode Either condition is met:
·

"Clearance Warning (Clearance Sonar)" is not displayed on the "Bus Check" screen.

·

"Clearance Warning ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of clearance warning ECU assembly

·

Clearance warning ECU assembly CAN branch wire or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

E207358E03
5.813,0.734 6.224,0.916 0.411,0.181 10 CANH 5.561,0.659 5.717,0.841 0.156,0.181 10 3 5.561,1.102 5.717,1.284 0.156,0.181 10 5 1.918,0.659 2.074,0.841 0.156,0.181 10 5 1.949,1.102 2.121,1.284 0.171,0.181 10 16 0.569,1.579 0.825,1.760 0.256,0.181 10 F73 0.569,1.747 2.155,1.928 1.586,0.181 10 No. 6 Junction Connector 5.385,3.546 5.642,3.727 0.256,0.181 10 F12 5.813,1.176 6.201,1.357 0.387,0.181 10 CANL 5.535,2.682 5.706,2.863 0.171,0.181 10 17 5.813,2.756 6.216,2.937 0.403,0.181 10 GND1 5.535,2.219 5.706,2.400 0.171,0.181 10 15 5.813,2.292 5.977,2.474 0.164,0.181 10 IG 3.453,2.168 4.525,2.349 1.073,0.181 10 ECU-IG No. 1 1.274,2.292 3.019,2.474 1.745,0.181 10 from IG1 NO. 1 Relay 5.384,3.717 6.934,4.036 1.551,0.319 10 Clearance Warning ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U166180E02
1.365,1.135 1.729,1.604 1.729,1.604 1.917,1.604 false 1.156,1.135 0.792,1.604 0.792,1.604 0.604,1.604 false 1.594,0.406 2.021,0.615 0.427,0.208 10 false F12 0.063,0.042 0.365,0.26 0.302,0.219 10 false *a 0.104,1.521 0.625,1.781 0.521,0.26 10 false CANH 1.958,1.521 2.448,1.708 0.49,0.188 10 false CANL

Disconnect the F12 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F12-3 (CANH) - F12-5 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CLEARANCE WARNING ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166181E02
1.719,1.271 2.083,1.74 2.083,1.74 2.271,1.74 false 1.5,1.271 1.135,1.74 1.135,1.74 0.958,1.74 false 1.573,0.406 1.938,0.594 0.365,0.188 10 false F12 0.063,0.042 0.323,0.271 0.26,0.229 10 false *a 0.698,1.667 1.031,1.938 0.333,0.271 10 false IG 2.313,1.667 2.802,1.906 0.49,0.24 10 false GND1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-17 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-15 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR