Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either Condition is met:
·

"Airbag" is not displayed on the "Bus Check" screen.

·

"Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of center airbag sensor assembly

·

Center airbag sensor assembly CAN branch wire or connector

·

Center airbag sensor assembly



For vehicles with an airbag system.


WIRING DIAGRAM

C358112E01
0.542,2.052 2.469,2.552 1.927,0.5 10 false No. 1 Junction Connector 0.542,1.885 1.115,2.083 0.573,0.198 10 false E72 5.188,5.021 6.625,5.698 1.438,0.677 10 false Center Airbag Sensor Assembly 5.208,4.844 5.781,5.042 0.573,0.198 10 false E47 2.698,2.688 3.854,3.115 1.156,0.427 10 false from IG2 Relay 4.563,2.542 5.167,2.75 0.604,0.208 10 false IGN 5.479,1.125 6.083,1.333 0.604,0.208 10 false CANH 5.479,1.542 6.083,1.75 0.604,0.208 10 false CANL 5.479,2.698 6.083,2.906 0.604,0.208 10 false IG2 5.5,3.438 6.104,3.646 0.604,0.208 10 false E1 5.5,4.177 6.104,4.385 0.604,0.208 10 false E2 5.219,1 5.531,1.198 0.313,0.198 10 false 13 5.219,1.427 5.531,1.625 0.313,0.198 10 false 22 5.198,2.583 5.51,2.781 0.313,0.198 10 false 21 5.208,3.333 5.521,3.531 0.313,0.198 10 false 25 5.208,4.063 5.521,4.26 0.313,0.198 10 false 26 1.833,1 2.146,1.198 0.313,0.198 10 false 4 1.802,1.427 2.115,1.625 0.313,0.198 10 false 15

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U165070E02
2.021,0.99 2.49,0.406 2.49,0.406 2.573,0.406 false 2.135,1.271 2.49,1.677 2.49,1.677 2.573,1.677 false 0.417,1.01 0.792,1.208 0.375,0.198 10 false E47 2.615,0.323 3.198,0.583 0.583,0.26 10 false CANH 0.063,0 0.271,0.177 0.208,0.177 10 false *a 2.615,1.583 3.115,1.802 0.5,0.219 10 false CANL

Disconnect the E47 center airbag sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E47-13 (CANH) - E47-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165071E01
0.403,1.015 0.679,1.156 0.276,0.141 10 E47 2.615,0.906 3.049,1.050 0.434,0.145 10 IG2 0.06,0.025 0.273,0.203 0.213,0.178 10 *a 2.3,1.682 2.706,1.824 0.406,0.143 10 E1 0.964,1.709 1.166,1.851 0.202,0.143 10 E2 2.261,1.198 2.494,0.982 2.494,0.982 2.582,0.982 false 1.798,1.289 2.134,1.757 2.134,1.757 2.266,1.757 false 1.672,1.289 1.372,1.785 1.372,1.785 1.23,1.785 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-25 (E1) - Body ground Always Below 1 Ω
E47-26 (E2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E47-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR