Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item DTC Detection Condition Trouble Area
4WD Control ECU Communication Stop Mode Either Condition is met:
·

""Four Wheel Drive Control" is not displayed on the "Bus Check" screen.

·

"4WD Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of 4WD control ECU

·

4WD control ECU CAN branch wire or connector

·

4WD control ECU



WIRING DIAGRAM

E211915E03
5.802,0.74 6.302,0.948 0.5,0.208 10 false CAN+ 1.917,0.594 2.135,0.844 0.219,0.25 10 false 5 1.917,1.031 2.135,1.25 0.219,0.219 10 false 16 0.573,1.51 0.833,1.688 0.26,0.177 10 false E72 0.573,1.677 2.156,1.854 1.583,0.177 10 false No. 1 Junction Connector 5.813,1.188 6.302,1.427 0.49,0.24 10 false CAN- 5.813,2.771 6.26,3.01 0.448,0.24 10 false GND 5.813,2.271 6.135,2.5 0.323,0.229 10 false IG 3.708,2.104 4.031,2.281 0.323,0.177 10 false 4WD 1.25,2.281 2.719,2.542 1.469,0.26 10 false from IG1 NO. 1 Relay 5.594,3.646 6.813,3.865 1.219,0.219 10 false 4WD Control ECU 5.469,0.521 5.75,0.719 0.281,0.198 10 false 19 5.417,0.75 5.719,0.927 0.302,0.177 10 false A27 5.469,0.979 5.698,1.167 0.229,0.188 10 false 20 5.427,1.188 5.76,1.396 0.333,0.208 10 false A27 5.51,2.021 5.75,2.229 0.24,0.208 10 false 3 5.427,2.292 5.771,2.51 0.344,0.219 10 false A28 5.51,2.542 5.708,2.708 0.198,0.167 10 false 4 5.427,2.76 5.76,2.979 0.333,0.219 10 false A28

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U166183E02
2.5,1.146 2.729,0.865 2.729,0.865 2.875,0.865 false 2.583,1.188 2.719,1.375 2.719,1.375 2.865,1.375 false 1.573,0.406 1.969,0.604 0.396,0.198 10 false A27 0.063,0.042 0.354,0.271 0.292,0.229 10 false *a 2.906,0.781 3.396,0.958 0.49,0.177 10 false CAN+ 2.896,1.302 3.354,1.458 0.458,0.156 10 false CAN-

Disconnect the A27 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A27-19 (CAN+) - A27-20 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4WD CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)
a.
U166192E01
0.457,0.988 0.721,1.131 0.264,0.143 10 A28 0.088,0.038 0.244,0.219 0.156,0.181 10 *a 2.369,0.515 2.533,0.696 0.164,0.181 10 IG 2.606,1.067 2.932,1.248 0.326,0.181 10 GND 2.004,0.89 2.187,0.598 2.187,0.598 2.339,0.598 false 2.17,0.974 2.422,1.148 2.422,1.148 2.574,1.148 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the A28 4WD control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-4 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A28-3 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR