Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on the "Bus Check" screen.

·

"Main Body ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside main body ECU (cowl side junction block LH)

·

Main body ECU (cowl side junction block LH) CAN branch wire or connector

·

Main body ECU (cowl side junction block LH)



WIRING DIAGRAM

C175124E03
5.597,0.583 6.080,0.781 0.483,0.198 10 CANH 5.376,0.482 5.493,0.652 0.118,0.171 10 5 5.597,1.027 6.080,1.224 0.483,0.198 10 CANL 0.386,1.409 0.690,1.596 0.304,0.187 10 E75 0.386,1.58 1.990,1.735 1.604,0.155 10 No. 3 Junction Connector 2.359,2.444 3.167,2.641 0.808,0.198 10 from Battery 5.376,0.925 5.493,1.096 0.118,0.171 10 6 3.682,2.463 3.896,2.661 0.214,0.198 10 2A 3.744,2.269 3.945,2.440 0.201,0.171 10 1 3.682,2.938 3.896,3.136 0.214,0.198 10 2D 3.677,2.744 3.878,2.915 0.201,0.171 10 62 1.686,0.501 1.887,0.672 0.201,0.171 10 4 1.686,0.95 1.887,1.121 0.201,0.171 10 15 5.38,1.771 5.510,1.941 0.130,0.171 10 1 5.597,2.479 6.080,2.677 0.483,0.198 10 ALTB 4.302,2.302 5.159,2.499 0.857,0.198 10 DOOR NO. 1 5.597,2.942 6.080,3.140 0.483,0.198 10 GND2 5.012,3.607 6.908,3.966 1.895,0.360 10 Main Body ECU (Cowl Side Junction Block LH) 5.012,3.418 5.282,3.598 0.270,0.179 10 E3 5.597,1.863 6.080,2.061 0.483,0.198 10 GND3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U166107E01
0.81,1.162 1.002,1.305 0.193,0.143 10 E3 0.052,0.044 0.222,0.205 0.170,0.161 10 *a 2.397,1.427 2.819,1.572 0.422,0.145 10 CANH 2.336,0.954 2.758,1.099 0.422,0.145 10 CANL 1.873,1.301 2.168,1.035 2.168,1.035 2.317,1.035 false 1.988,1.304 2.226,1.499 2.226,1.499 2.375,1.499 false

Disconnect the E3 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E3-5 (CANH) - E3-6 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U165296E01
3.902,1.198 4.047,1.497 4.047,1.497 4.161,1.497 false 0.047,0.042 0.229,0.185 0.183,0.143 10 *a 4.885,0.042 5.067,0.185 0.183,0.143 10 *b 4.177,1.427 4.593,1.568 0.416,0.141 10 GND2 1.319,0.289 1.506,0.430 0.187,0.141 10 2A 1.23,1.223 1.057,1.409 1.057,1.409 0.965,1.409 false 0.556,1.344 1.009,1.485 0.453,0.141 10 ALTB 3.348,0.382 3.545,0.523 0.196,0.141 10 2D 5.517,0.21 5.705,0.350 0.187,0.141 10 E3 5.8,0.943 5.952,0.813 5.952,0.813 6.067,0.813 false 6.082,0.744 6.498,0.885 0.416,0.141 10 GND3

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 (ALTB) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-62 (GND2) - Body ground Always Below 1 Ω
E3-1 (GND3) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR