Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0104  Lost Communication with Driving Support ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0104 There is no communication from the distance control ECU assembly.
·

Power source circuit of distance control ECU assembly

·

Distance control ECU assembly CAN branch wire or connector

·

Distance control ECU assembly



For vehicles with a dynamic radar cruise control system.


WIRING DIAGRAM

C173460E04
5.677,1.208 6.125,1.385 0.448,0.177 10 false CANH 5.479,1.125 5.604,1.302 0.125,0.177 10 false 8 5.677,1.646 6.125,1.823 0.448,0.177 10 false CANL 5.479,1.573 5.604,1.75 0.125,0.177 10 false 9 1.781,1.125 1.906,1.302 0.125,0.177 10 false 4 1.781,1.573 1.979,1.75 0.198,0.177 10 false 15 5.677,3 6.125,3.177 0.448,0.177 10 false B 3.729,2.823 4.635,3 0.906,0.177 10 false ECU-IG No. 3 2.802,4.385 4.188,4.698 1.385,0.313 10 false from IG NO. 4 Relay 0.5,2.198 2.146,2.375 1.646,0.177 10 false No. 5 Junction Connector 0.5,2.031 0.813,2.208 0.313,0.177 10 false E68 5.479,2.906 5.604,3.083 0.125,0.177 10 false 1 5.677,3.792 6.125,3.969 0.448,0.177 10 false GND 5.417,4.583 5.813,4.792 0.396,0.208 10 false E108 5.417,4.771 6.823,5.458 1.406,0.688 10 false Distance Control ECU Assembly 5.406,3.708 5.594,3.885 0.188,0.177 10 false 12

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (DISTANCE CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (DISTANCE CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U165215E01
2.739,1.009 3.083,1.150 0.345,0.141 10 E108 0.039,0.039 0.311,0.179 0.273,0.141 10 *a 0.475,1.436 0.896,1.577 0.421,0.141 10 CANL 1.522,1.091 1.101,1.513 1.101,1.513 0.976,1.513 false 0.728,1.759 1.149,1.900 0.421,0.141 10 CANH 1.605,1.091 1.378,1.836 1.378,1.836 1.253,1.836 false

Disconnect the E108 distance control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E108-8 (CANH) - E108-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Distance Control ECU assembly)



OK

4.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE DISTANCE CONTROL ECU ASSEMBLY BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165216E01
2.694,1.035 3.036,1.176 0.342,0.141 10 E108 0.039,0.039 0.311,0.179 0.273,0.141 10 *a 0.419,1.153 0.757,1.294 0.338,0.141 10 GND 2.319,0.967 2.477,0.8 2.477,0.8 2.602,0.8 false 1.123,1.068 0.964,1.235 0.964,1.235 0.84,1.235 false 2.638,0.722 3.059,0.863 0.421,0.141 10 B

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E108-1 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E108-12 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Distance Control ECU assembly)


OK

REPLACE DISTANCE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR