Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0199  Lost Communication with "Door Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0199 There is no communication from the outer mirror control ECU assembly.
·

Power source circuit of outer mirror control ECU assembly

·

Outer mirror control ECU assembly CAN branch wire or connector

·

Outer mirror control ECU assembly



For vehicles with seat memory.


WIRING DIAGRAM

C158947E13
0.635,2.906 2.313,3.125 1.677,0.219 10 false No. 8 Junction Connector 5.49,1.969 5.813,2.188 0.323,0.219 10 false I18 0.646,2.76 0.979,2.917 0.333,0.156 10 false E76 1.927,1.823 2.063,2 0.135,0.177 10 false 5 1.927,2.271 2.125,2.448 0.198,0.177 10 false 16 5.854,3.115 6.375,3.302 0.521,0.188 10 false B 5.854,3.771 6.375,3.958 0.521,0.188 10 false ACC 5.5,2.406 5.813,2.646 0.313,0.24 10 false I18 5.5,3.781 5.781,4.021 0.281,0.24 10 false I17 5.49,3.135 5.771,3.354 0.281,0.219 10 false I17 5.542,2.927 5.729,3.104 0.188,0.177 10 false 3 5.552,3.583 5.781,3.76 0.229,0.177 10 false 4 4.406,2.948 4.708,3.104 0.302,0.156 10 false MIR 4.375,3.635 4.719,3.844 0.344,0.208 10 false ACC 2.438,5.167 2.896,5.521 0.458,0.354 10 false from Battery 3.271,5.167 3.906,5.563 0.635,0.396 10 false from ACC Relay 5.865,4.438 6.385,4.625 0.521,0.188 10 false GND 5.49,4.448 5.813,4.677 0.323,0.229 10 false I17 5.552,4.25 5.781,4.427 0.229,0.177 10 false 9 5.854,1.958 6.375,2.146 0.521,0.188 10 false CANH 5.854,2.396 6.375,2.583 0.521,0.188 10 false CANL 5.531,1.76 5.719,1.938 0.188,0.177 10 false 1 5.5,2.208 5.729,2.385 0.229,0.177 10 false 21 5.427,5.271 7.031,5.646 1.604,0.375 10 false Outer Mirror Control ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicle with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U165163E01
0.518,1.474 0.613,2.061 0.613,2.061 0.722,2.061 false 0.897,1.829 0.819,1.829 0.819,1.829 0.509,1.325 false 0.069,0.041 0.252,0.193 0.184,0.151 10 *a 1.592,0.47 1.805,0.607 0.213,0.137 10 I18 0.917,1.752 1.469,1.890 0.552,0.137 10 CANH 0.731,1.984 1.166,2.121 0.435,0.137 10 CANL

Disconnect the I18 outer mirror control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I18-1 (CANH) - I18-21 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165165E01
2.011,1.481 2.298,1.842 2.298,1.842 2.412,1.842 false 2.22,1.074 2.45,0.917 2.45,0.917 2.598,0.917 false 2.429,0.648 2.295,0.648 2.295,0.648 2.02,1.074 false 0.075,0.04 0.407,0.307 0.332,0.267 10 *a 1.596,0.463 1.809,0.601 0.214,0.139 10 I17 2.455,0.572 2.669,0.710 0.214,0.139 10 B 2.613,0.841 2.945,0.980 0.332,0.139 10 ACC 2.429,1.772 2.761,1.911 0.332,0.139 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the I17 outer mirror control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-9 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I17-3 (B) - Body ground Always 11 to 14 V
I17-4 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)


OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR