Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the position control ECU and switch.
·

Power source circuit of position control ECU and switch

·

Position control ECU and switch CAN branch wire or connector

·

Position control ECU and switch



For vehicles with seat memory.


WIRING DIAGRAM

C150448E06
5.576,1.709 6.010,1.903 0.434,0.195 10 MPX2 5.576,1.258 6.061,1.469 0.485,0.211 10 MPX1 5.576,3.408 6.069,3.581 0.493,0.174 10 GND 0.465,2.073 0.768,2.234 0.302,0.161 10 E76 0.465,2.255 2.243,2.447 1.777,0.192 10 No. 8 Junction Connector 1.722,1.172 1.913,1.335 0.191,0.163 10 4 1.702,1.618 1.907,1.763 0.205,0.145 10 15 3.601,2.416 4.573,2.590 0.972,0.174 10 FR P/SEAT LH 2.491,4.547 2.997,4.875 0.506,0.327 10 from Battery 5.35,1.092 5.458,1.265 0.108,0.173 10 5 5.35,1.539 5.474,1.707 0.124,0.169 10 1 5.346,3.23 5.460,3.391 0.114,0.161 10 1 5.34,2.382 5.454,2.559 0.115,0.176 10 5 5.312,4.088 6.773,4.419 1.461,0.331 10 Position Control ECU and Switch 5.268,3.398 5.574,3.568 0.306,0.170 10 c14 5.268,2.554 5.574,2.724 0.306,0.170 10 c14 5.268,1.71 5.574,1.880 0.306,0.170 10 c15 5.268,1.258 5.574,1.428 0.306,0.170 10 c15 5.576,2.548 5.950,2.742 0.374,0.195 10 +B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicle with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (POSITION CONTROL ECU AND SWITCH CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (POSITION CONTROL ECU AND SWITCH CAN BRANCH WIRE)
a.
U165170E01
1.481,1.54 1.272,1.71 1.272,1.71 1.157,1.71 false 1.481,1.26 1.272,1.09 1.272,1.09 1.157,1.09 false 1.481,1.54 1.272,1.71 1.272,1.71 1.157,1.71 false 1.481,1.26 1.272,1.09 1.272,1.09 1.157,1.09 false 0.054,0.059 0.225,0.211 0.171,0.152 10 *a 0.647,1.634 1.060,1.772 0.413,0.137 10 MPX1 0.66,1.001 1.063,1.138 0.402,0.137 10 MPX2 1.575,0.409 1.816,0.550 0.241,0.140 10 c15

Disconnect the c15 position control ECU and switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
c15-5 (MPX1) - c15-1 (MPX2) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Position Control ECU and Switch)



OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POSITION CONTROL ECU AND SWITCH CAN BRANCH WIRE OR CONNECTOR (MPX1, MPX2)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH - BATTERY AND BODY GROUND)
a.
U165166E01
1.202,1.481 1.036,1.722 1.036,1.722 0.921,1.722 false 1.165,1.074 0.967,0.84 0.967,0.84 0.818,0.84 false 0.075,0.04 0.407,0.307 0.332,0.267 10 *a 1.56,0.45 1.802,0.589 0.242,0.139 10 c14 0.668,1.642 0.882,1.780 0.214,0.139 10 +B 0.394,0.754 0.726,0.892 0.332,0.139 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the c14 position control ECU and switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c14-1 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
c14-5 (+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Position Control ECU and Switch)


OK

REPLACE POSITION CONTROL ECU AND SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR