Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U1115  Lost Communication with Tilt and Telescopic Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1115 There is no communication from the multiplex tilt and telescopic ECU.
·

Power source circuit of multiplex tilt and telescopic ECU

·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Multiplex tilt and telescopic ECU



For vehicles with the power tilt and power telescopic steering column system.


WIRING DIAGRAM

C150442E12
5.814,1.899 6.307,2.073 0.493,0.174 10 CANP 5.814,2.351 6.285,2.517 0.471,0.165 10 CANN 5.814,3.424 6.253,3.635 0.439,0.211 10 ECUB 5.814,4.648 6.297,4.825 0.483,0.177 10 GND 1.923,1.808 2.114,1.970 0.191,0.163 10 3 1.923,2.262 2.128,2.406 0.205,0.145 10 14 2.589,5.176 3.094,5.499 0.505,0.324 10 from Battery 5.077,5.352 5.394,5.527 0.317,0.175 10 E27 5.541,2.251 5.761,2.424 0.220,0.173 10 14 5.581,1.821 5.792,1.990 0.211,0.169 10 5 5.581,2.707 5.704,2.855 0.123,0.148 10 2 5.581,3.337 5.751,3.498 0.170,0.161 10 9 5.541,4.538 5.715,4.714 0.174,0.176 10 11 5.814,4.065 6.188,4.260 0.374,0.195 10 IG 5.818,2.802 6.192,2.996 0.374,0.195 10 +B 5.581,3.99 5.755,4.166 0.174,0.176 10 8 4.068,2.682 4.522,2.847 0.454,0.166 10 TI&TE 3.183,5.176 3.959,5.577 0.776,0.401 10 from IG1 NO. 1 Relay 0.625,2.713 0.927,2.873 0.302,0.161 10 E76 0.625,2.895 2.402,3.087 1.777,0.192 10 No. 8 Junction Connector 5.069,5.541 7.165,5.758 2.096,0.216 10 Multiplex Tilt and Telescopic ECU 4.009,3.298 4.536,3.473 0.526,0.176 10 ECU-B1 3.851,3.952 5.009,4.128 1.158,0.176 10 ECU-IG No. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC CAN ECU BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC CAN ECU BRANCH WIRE)
a.
U165171E01
1.588,0.426 1.853,0.563 0.265,0.137 10 E27 0.079,0.056 0.368,0.193 0.289,0.137 10 *a 1.725,1.537 1.303,1.961 1.303,1.961 1.149,1.961 false 2.575,0.658 2.363,0.658 2.363,0.658 1.757,1.238 false 0.633,1.879 1.052,2.016 0.419,0.137 10 CANN 2.598,0.576 3.017,0.713 0.419,0.137 10 CANP

Disconnect the E27 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E27-5 (CANP) - E27-14 (CANN) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)
a.
U165172E01
1.587,0.426 1.855,0.563 0.268,0.137 10 E27 0.079,0.056 0.368,0.193 0.289,0.137 10 *a 1.249,1.512 1.043,1.936 1.043,1.936 0.888,1.936 false 2.705,1.042 2.545,1.042 2.545,1.042 2.37,1.193 false 0.813,0.793 1.025,0.793 1.025,0.793 1.261,1.193 false 2.711,0.721 2.499,0.721 2.499,0.721 2.18,1.193 false 0.464,1.853 0.809,1.990 0.345,0.137 10 GND 2.724,0.636 2.916,0.773 0.192,0.137 10 IG 0.581,0.708 0.773,0.844 0.192,0.137 10 +B 2.726,0.964 3.144,1.101 0.419,0.137 10 ECUB

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E27-2 (+B) - Body ground Always 11 to 14 V
E27-9 (ECUB) - Body ground Always 11 to 14 V
E27-8 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E27-11 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR