Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  AFS ECU Communication Stop Mode  


DESCRIPTION

Detection Item DTC Detection Condition Trouble Area
AFS ECU Communication Stop Mode Either condition is met:
·

"Headlight swivel (AFS)" is not displayed on the "Bus Check" screen.

·

"AFS ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of headlight swivel ECU assembly

·

Headlight swivel ECU assembly CAN branch wire or connector

·

Headlight swivel ECU assembly



For vehicles with a dynamic headlight auto leveling.


WIRING DIAGRAM

E207358E06
5.813,0.734 6.224,0.916 0.411,0.181 10 MPX1 5.542,0.659 5.717,0.841 0.174,0.181 10 12 5.542,1.102 5.717,1.284 0.174,0.181 10 13 1.918,0.659 2.074,0.841 0.156,0.181 10 3 1.949,1.102 2.121,1.284 0.171,0.181 10 14 0.709,1.579 1.012,1.760 0.303,0.181 10 E72 0.709,1.747 2.296,1.928 1.586,0.181 10 No. 1 Junction Connector 5.567,3.579 5.940,3.760 0.372,0.181 10 E101 5.813,1.176 6.242,1.357 0.429,0.181 10 MPX2 5.535,2.682 5.706,2.863 0.171,0.181 10 22 5.813,2.756 6.216,2.937 0.403,0.181 10 E1 5.535,2.219 5.706,2.400 0.171,0.181 10 15 5.813,2.292 5.977,2.474 0.164,0.181 10 IG 3.453,2.168 4.525,2.349 1.073,0.181 10 ECU-IG No. 3 1.274,2.292 3.019,2.474 1.745,0.181 10 from IG1 NO. 4 Relay 5.566,3.75 6.948,4.069 1.382,0.319 10 Headlight Swivel ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U165146E01
1.082,1.287 0.911,1.591 0.911,1.591 0.739,1.591 false 0.693,1.049 0.822,1.049 0.822,1.049 0.984,1.236 false 0.181,0.961 0.603,1.098 0.422,0.137 10 MPX2 0.247,1.509 0.669,1.647 0.422,0.137 10 MPX1 0.072,0.038 0.494,0.176 0.422,0.137 10 *a 2.855,1.042 3.200,1.180 0.346,0.137 10 E101

Disconnect the E101 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E101-12 (MPX1) - E101-13 (MPX2) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Headlight Swivel ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (MPX1, MPX2)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165147E01
2.501,1.405 2.671,1.709 2.671,1.709 2.843,1.709 false 2.865,1.631 3.064,1.769 0.199,0.137 10 IG 2.379,1.876 2.578,2.013 0.199,0.137 10 E1 0.072,0.038 0.494,0.176 0.422,0.137 10 *a 0.219,1.264 0.565,1.402 0.346,0.137 10 E101 1.877,1.408 2.176,1.938 2.176,1.938 2.348,1.938 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-22 (E1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E101-15 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Headlight Swivel ECU Assembly)


OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR