Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U1117  Lost Communication with Accessory Gateway  B2779  Engine Starter Communication Malfunction  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1117 There is no communication from the accessory bus buffer
·

Accessory bus buffer CAN branch wire or connector

·

Accessory bus buffer


B2779 There is no communication from the accessory bus buffer
·

Accessory bus buffer CAN branch wire or connector

·

Accessory bus buffer



WIRING DIAGRAM

C140665E02
1.2,2.876 2.813,3.058 1.613,0.181 10 No. 9 Junction Connector 1.684,1.411 2.094,1.592 0.411,0.181 10 CANH 2.207,1.329 2.363,1.510 0.156,0.181 10 3 2.207,2.119 2.378,2.301 0.171,0.181 10 14 4.837,1.329 4.993,1.510 0.156,0.181 10 1 4.837,2.119 4.993,2.301 0.156,0.181 10 2 1.684,2.206 2.071,2.387 0.387,0.181 10 CANL 5.101,1.411 5.511,1.592 0.411,0.181 10 CAN+ 5.101,2.206 5.488,2.387 0.387,0.181 10 CAN- 5.009,2.887 6.488,3.069 1.479,0.181 10 Accessory Bus Buffer 1.198,2.714 1.470,2.896 0.272,0.181 10 E73 5.005,2.725 5.277,2.907 0.272,0.181 10 E6

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (ACCESSORY BUS BUFFER CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (ACCESSORY BUS BUFFER CAN BRANCH WIRE)
a.

Disconnect the E6 accessory bus buffer connector.


U166186E02
1.542,1.354 1.354,1.688 false 1.896,1.354 2.073,1.677 false 0.094,0.073 0.26,0.229 0.167,0.156 10 false *a 1.135,1.708 1.646,1.906 0.51,0.198 10 false CAN+ 1.896,1.708 2.573,1.969 0.677,0.26 10 false CAN- 0.75,1.052 1.063,1.271 0.313,0.219 10 false E6

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E6-1 (CAN+) - E6-2 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Accessory Bus Buffer)



OK

REPLACE ACCESSORY BUS BUFFER

NG

REPAIR OR REPLACE ACCESSORY BUS BUFFER CAN BRANCH WIRE OR CONNECTOR (CAN+, CAN-)