Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U110B  Lost Communication with Parking Assist Control Module "B"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U110B There is no communication from the parking assist ECU.
·

Power source circuit of parking assist ECU

·

Parking assist ECU CAN branch wire or connector

·

Parking assist ECU



For vehicles with a side monitor system.


WIRING DIAGRAM

C235415E02
5.244,0.644 5.417,0.781 0.172,0.137 10 40 5.201,0.854 5.460,0.991 0.259,0.137 10 F76 5.244,1.232 5.417,1.369 0.172,0.137 10 39 5.201,1.442 5.460,1.580 0.259,0.137 10 F76 5.28,2.222 5.382,2.359 0.101,0.137 10 1 5.201,2.433 5.460,2.571 0.259,0.137 10 F75 5.28,3.964 5.382,4.102 0.101,0.137 10 4 5.201,4.176 5.460,4.313 0.259,0.137 10 F75 5.28,3.404 5.382,3.541 0.101,0.137 10 9 5.201,3.616 5.460,3.753 0.259,0.137 10 F75 5.28,2.81 5.382,2.948 0.101,0.137 10 8 5.201,3.022 5.460,3.159 0.259,0.137 10 F75 5.662,1.441 6.281,1.579 0.619,0.137 10 CANL 5.662,0.854 6.281,0.991 0.619,0.137 10 CANH 5.662,3.02 6.281,3.157 0.619,0.137 10 IG 5.662,3.614 6.281,3.752 0.619,0.137 10 ACC 5.662,2.432 6.281,2.569 0.619,0.137 10 +B 0.861,2.43 1.642,2.567 0.781,0.137 10 from Battery 0.613,3.614 1.640,3.752 1.026,0.137 10 from ACC Relay 5.662,4.198 6.281,4.335 0.619,0.137 10 GND1 0.278,3.003 1.637,3.141 1.358,0.137 10 from IG1 NO. 1 Relay 0.501,1.76 1.454,1.897 0.952,0.137 10 F73 0.501,1.9 2.148,2.037 1.647,0.137 10 No. 6 Junction Connector 1.594,1.329 1.792,1.467 0.198,0.137 10 16 1.594,0.742 1.792,0.879 0.198,0.137 10 5 2.393,2.29 3.124,2.427 0.731,0.137 10 RAD NO. 1 2.577,3.474 2.892,3.612 0.316,0.137 10 ACC 2.293,2.866 3.171,3.003 0.878,0.137 10 ECU-IG No. 1 5.491,4.917 6.724,5.061 1.232,0.144 10 Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU CAN BRANCH WIRE)
a.
U165261E01
1.644,0.237 1.908,0.374 0.264,0.136 10 F76 0.029,0.034 0.198,0.195 0.170,0.161 10 *a 0.369,1.545 0.766,1.684 0.397,0.139 10 CANL 0.246,1.221 0.667,1.360 0.420,0.139 10 CANH 1.08,1.133 0.943,1.292 0.943,1.292 0.751,1.292 false 1.14,1.151 1.046,1.621 1.046,1.621 0.854,1.621 false

Disconnect the F76 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F76-40 (CANH) - F76-39 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)



OK

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE PARKING ASSIST ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U165262E01
1.64,0.248 1.904,0.384 0.264,0.136 10 F75 0.063,0.058 0.233,0.219 0.170,0.161 10 *a 2.556,1.53 2.954,1.669 0.397,0.139 10 IG 2.685,0.881 2.890,1.020 0.205,0.139 10 +B 0.369,0.881 0.785,1.020 0.416,0.139 10 GND1 1.985,1.269 2.305,1.614 2.305,1.614 2.539,1.614 false 1.269,1.121 1.041,0.953 1.041,0.953 0.875,0.953 false 2.267,1.121 2.495,0.953 2.495,0.953 2.661,0.953 false 2.367,1.811 2.764,1.950 0.397,0.139 10 ACC 1.92,1.261 2.115,1.895 2.115,1.895 2.35,1.895 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the F75 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-4 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F75-1 (+B) - Body ground Always 11 to 14 V
F75-9 (ACC) - Body ground Ignition switch ACC 11 to 14 V
F75-8 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR