Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U1110  Lost Communication with Clearance Sonar Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1110 There is no communication from the clearance warning ECU assembly.
·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly CAN branch wire or connector

·

Clearance warning ECU assembly



For vehicles with the TOYOTA parking assist-sensor system and without the side monitor system.


WIRING DIAGRAM

C175117E07
5.616,0.906 6.050,1.101 0.434,0.195 10 CANH 5.616,1.378 6.101,1.590 0.485,0.211 10 CANL 5.616,2.702 6.223,2.876 0.607,0.174 10 GND1 5.616,2.225 5.821,2.390 0.205,0.165 10 IG 0.465,1.749 0.768,1.910 0.302,0.161 10 F73 0.465,1.915 2.243,2.107 1.777,0.192 10 No. 6 Junction Connector 1.722,0.868 1.913,1.031 0.191,0.163 10 5 1.702,1.314 1.907,1.458 0.205,0.145 10 16 3.966,2.116 4.844,2.290 0.878,0.174 10 ECU-IG No. 1 1.262,2.235 2.632,2.419 1.370,0.184 10 from IG1 NO. 1 Relay 5.41,0.855 5.516,1.028 0.107,0.173 10 3 5.41,1.298 5.512,1.467 0.103,0.169 10 5 5.362,2.615 5.574,2.777 0.212,0.161 10 17 5.356,2.15 5.529,2.326 0.174,0.176 10 15 5.273,3.326 5.575,3.487 0.302,0.161 10 F12 5.273,3.492 6.865,3.850 1.592,0.357 10 Clearance Warning ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U166180E02
1.365,1.135 1.729,1.604 1.729,1.604 1.917,1.604 false 1.156,1.135 0.792,1.604 0.792,1.604 0.604,1.604 false 1.594,0.406 2.021,0.615 0.427,0.208 10 false F12 0.063,0.042 0.365,0.26 0.302,0.219 10 false *a 0.104,1.521 0.625,1.781 0.521,0.26 10 false CANH 1.958,1.521 2.448,1.708 0.49,0.188 10 false CANL

Disconnect the F12 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F12-3 (CANH) - F12-5 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166182E02
1.698,1.281 1.917,1.594 1.917,1.594 2.104,1.594 false 1.479,1.281 1.219,1.583 1.219,1.583 1.031,1.583 false 1.594,0.406 1.979,0.615 0.385,0.208 10 false F12 0.063,0.042 0.396,0.302 0.333,0.26 10 false *a 0.813,1.51 1.083,1.719 0.271,0.208 10 false IG 2.146,1.51 2.677,1.708 0.531,0.198 10 false GND1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-15 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-17 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR