Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U0327  Software Incompatibility with Vehicle Security Control Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0327 There is no communication from the certification ECU (smart key ECU assembly).
·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) CAN branch wire or connector

·

Certification ECU (smart key ECU assembly)



For vehicles with an entry and start system.


WIRING DIAGRAM

C176044E08
5.822,1.186 6.315,1.360 0.493,0.174 10 CANH 5.822,1.639 6.293,1.804 0.471,0.165 10 CANL 5.822,2.703 6.189,2.869 0.367,0.167 10 ACC 5.822,3.935 6.305,4.113 0.483,0.177 10 E 1.963,1.095 2.154,1.258 0.191,0.163 10 2 1.931,1.549 2.136,1.694 0.205,0.145 10 13 2.503,4.533 3.166,4.851 0.663,0.317 10 from Battery 5.536,1.52 5.756,1.693 0.220,0.173 10 28 5.536,1.089 5.747,1.258 0.211,0.169 10 27 5.612,1.986 5.735,2.134 0.123,0.148 10 1 5.556,2.593 5.837,2.754 0.281,0.161 10 19 5.556,3.802 5.730,3.978 0.174,0.176 10 17 5.821,3.315 6.195,3.510 0.374,0.195 10 IG 5.826,2.081 6.200,2.275 0.374,0.195 10 +B 5.555,3.201 5.729,3.377 0.174,0.176 10 18 4.144,1.96 4.431,2.181 0.287,0.221 10 IMB 3.544,4.533 3.969,5.080 0.424,0.547 10 from IG2 Relay 3.028,4.533 3.452,5.080 0.424,0.547 10 from ACC Relay 0.633,2 0.935,2.161 0.302,0.161 10 E76 0.633,2.183 2.410,2.374 1.777,0.192 10 No. 8 Junction Connector 5.431,4.82 6.988,5.177 1.556,0.357 10 Certification ECU (Smart Key ECU Assembly) 4.125,2.585 4.555,2.738 0.430,0.153 10 ACC 4.13,3.202 4.426,3.378 0.297,0.176 10 IGN 5.431,4.646 5.738,4.816 0.306,0.170 10 E29

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CERTIFICATION ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (CERTIFICATION ECU CAN BRANCH WIRE)
a.
U166124E01
1.187,1.845 1.305,1.845 1.305,1.845 1.562,1.333 false 0.089,0.076 0.328,0.288 0.239,0.211 10 *a 1.587,0.402 1.851,0.542 0.264,0.140 10 E29 2.033,1.845 1.915,1.845 1.915,1.845 1.658,1.333 false 2.048,1.759 2.534,1.901 0.486,0.142 10 CANL 0.67,1.759 1.156,1.901 0.486,0.142 10 CANH

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E29-27 (CANH) - E29-28 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CERTIFICATION ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
a.
U166123E01
0.089,0.081 0.328,0.292 0.239,0.211 10 *a 3.204,0.691 3.337,0.838 0.133,0.147 10 E 0.121,0.697 0.326,0.839 0.205,0.142 10 +B 1.036,1.567 1.362,1.706 0.326,0.139 10 ACC 0.789,1.767 0.994,1.906 0.205,0.139 10 IG 1.673,0.407 1.937,0.547 0.264,0.140 10 E29 2.959,1.086 3.092,0.775 3.092,0.775 3.189,0.775 false 0.594,1.086 0.461,0.775 0.461,0.775 0.364,0.775 false 0.701,1.337 0.897,1.653 0.897,1.653 1.013,1.653 false 0.766,1.849 0.647,1.849 0.647,1.849 0.585,1.337 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E29-1 (+B) - Body ground Always 11 to 14 V
E29-18 (IG) - Body ground Ignition switch ON 11 to 14 V
E29-19 (ACC) - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-17 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR