Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U0127  Lost Communication with Tire Pressure Monitor Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0127 There is no communication from the tire pressure warning ECU.
·

Power source or inside of tire pressure warning ECU and receiver

·

Tire pressure warning ECU and receiver CAN branch wire or connector

·

Tire pressure warning ECU and receiver



For vehicles with an tire pressure warning system.


WIRING DIAGRAM

C150455E14
5.616,1.684 6.050,1.878 0.434,0.195 10 CN1 5.616,1.233 6.101,1.444 0.485,0.211 10 CP1 5.616,3.395 6.109,3.568 0.493,0.174 10 GN1 0.465,2.068 0.768,2.229 0.302,0.161 10 L58 0.465,2.25 2.432,2.442 1.967,0.192 10 No. 2 CAN Junction Connector 1.722,1.151 1.913,1.314 0.191,0.163 10 1 1.702,1.597 1.907,1.742 0.205,0.145 10 2 3.566,2.395 4.472,2.569 0.906,0.174 10 ECU-IG No. 4 2.058,4.526 3.342,4.708 1.284,0.182 10 from IG NO. 4 Relay 5.391,1.154 5.611,1.328 0.220,0.173 10 3 5.386,1.601 5.597,1.770 0.211,0.169 10 6 5.391,3.292 5.603,3.454 0.212,0.161 10 4 5.391,2.445 5.565,2.621 0.174,0.176 10 1 5.209,4.196 6.655,4.602 1.446,0.406 10 Tire Pressure Warning ECU and Receiver 5.616,2.535 5.989,2.729 0.374,0.195 10 IG1 5.223,4.008 5.717,4.182 0.493,0.174 10 L60

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU CAN BRANCH WIRE)
a.
U165406E01
0.052,0.067 0.229,0.226 0.178,0.158 10 *a 1.629,0.372 1.886,0.511 0.258,0.139 10 L60 0.461,0.65 0.874,0.789 0.413,0.139 10 CP1 0.521,1.724 0.944,1.862 0.423,0.139 10 CN1 1.189,1.438 1,1.812 1,1.812 0.905,1.812 false 1.189,1.054 0.935,0.721 0.935,0.721 0.841,0.721 false

Disconnect the L60 tire pressure warning ECU and receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L60-3 (CP1) - L60-6 (CN1) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)



OK

4.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE TIRE PRESSURE WARNING ECU CAN BRANCH WIRE OR CONNECTOR (CP1, CN1)

4.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU - BATTERY AND BODY GROUND)
a.
U165407E01
1.646,0.372 1.904,0.511 0.258,0.139 10 L60 0.052,0.067 0.229,0.226 0.178,0.158 10 *a 0.197,0.748 0.453,0.886 0.255,0.139 10 IG1 0.861,1.054 0.607,0.836 0.607,0.836 0.513,0.836 false 0.166,1.647 0.495,1.786 0.330,0.139 10 GN1 0.861,1.461 0.667,1.735 0.667,1.735 0.573,1.735 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L60-1 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-4 (GN1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR