Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U0114/38  Lost Communication with 4WD Control ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0114/38 There is no communication from the 4WD control ECU.
·

Power source circuit of 4WD control ECU

·

4WD control ECU CAN branch wire or connector

·

4WD control ECU



WIRING DIAGRAM

C158952E11
0.698,2.927 2.375,3.146 1.677,0.219 10 false No. 4 Junction Connector 5.813,3.063 6.333,3.25 0.521,0.188 10 false IG 5.813,3.729 6.333,3.917 0.521,0.188 10 false GND 5.479,3.719 5.833,3.927 0.354,0.208 10 false A28 5.469,3.063 5.896,3.281 0.427,0.219 10 false A28 5.552,2.854 5.74,3.031 0.188,0.177 10 false 3 5.552,3.521 5.781,3.698 0.229,0.177 10 false 4 4.375,2.844 4.833,3.063 0.458,0.219 10 false 4WD 2.708,4.188 4.344,4.427 1.635,0.24 10 false from IG1 NO. 1 Relay 5.813,1.896 6.333,2.083 0.521,0.188 10 false CAN+ 5.813,2.333 6.333,2.521 0.521,0.188 10 false CAN- 5.635,4.521 7.094,4.76 1.458,0.24 10 false 4WD Control ECU 5.469,1.906 5.823,2.083 0.354,0.177 10 false A27 0.708,2.75 1.083,2.979 0.375,0.229 10 false E74 1.927,1.802 2.177,1.99 0.25,0.188 10 false 6 1.917,2.25 2.156,2.448 0.24,0.198 10 false 17 5.51,1.698 5.719,1.875 0.208,0.177 10 false 19 5.521,2.156 5.781,2.344 0.26,0.188 10 false 20 5.469,2.344 5.823,2.521 0.354,0.177 10 false A27

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U165128E01
2.917,1.09 3.183,1.228 0.266,0.137 10 A27 0.203,1.265 0.622,1.402 0.419,0.137 10 CAN- 0.338,1.545 0.747,1.682 0.409,0.137 10 CAN+ 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 0.988,1.151 0.807,1.346 0.807,1.346 0.679,1.346 false 1.072,1.151 1.013,1.63 1.013,1.63 0.834,1.63 false

Disconnect the A27 4WD control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A27-19 (CAN+) - A27-20 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to 4WD Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4WD CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CAN+, CAN-)

4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)
a.
U165164E01
2.22,1.077 2.45,0.92 2.45,0.92 2.598,0.92 false 2.429,0.651 2.295,0.651 2.295,0.651 2.02,1.077 false 0.075,0.043 0.407,0.310 0.332,0.267 10 *a 1.556,0.397 1.820,0.536 0.265,0.139 10 A28 2.455,0.575 2.669,0.713 0.214,0.139 10 IG 2.621,0.847 2.953,0.985 0.332,0.139 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the A28 4WD control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A28-3 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-4 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR