Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is output when a malfunction in the LIN communication bus between the components related to certification is detected continuously 3 times.

DTC Code DTC Detection Condition Trouble Area
B2785 The certification ECU (smart key ECU assembly) detects a malfunction in the LIN communication bus between components related to certification continuously 3 times.
·

Certification ECU (smart key ECU assembly)

·

Main body ECU (cowl side junction block LH)

·

ID code box (immobiliser code ECU)

·

Steering lock ECU

·

Harness or connector



WIRING DIAGRAM

B173730E15
2.313,1.188 2.646,1.375 0.333,0.188 10 false LIN 2.635,1.021 2.885,1.25 0.25,0.229 10 false 10 1.51,1.979 1.833,2.156 0.323,0.177 10 false E29 1.51,2.146 3.083,2.563 1.573,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.406,4.052 1.938,4.271 0.531,0.219 10 false E28 1.406,4.24 3.813,4.438 2.406,0.198 10 false ID Code Box (Immobiliser Code ECU) 4.5,4.052 4.927,4.208 0.427,0.156 10 false E26 4.5,4.219 5.823,4.396 1.323,0.177 10 false Steering Lock ECU 4.552,3.333 4.969,3.542 0.417,0.208 10 false LIN 2.229,3.333 2.646,3.542 0.417,0.208 10 false LIN1 4.365,3.146 4.49,3.313 0.125,0.167 10 false 5 4.563,1.177 4.906,1.354 0.344,0.177 10 false LIN1 4.479,2.125 6.135,2.573 1.656,0.448 10 false Main Body ECU (Cowl Side Junction Block LH) 4.281,0.99 4.479,1.146 0.198,0.156 10 false 20 0.906,4.75 1.615,4.969 0.708,0.219 10 false : LIN Line 2.646,3.146 2.906,3.313 0.26,0.167 10 false 3 4.479,1.969 4.823,2.146 0.344,0.177 10 false 2D

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

When DTC B2785 and B2287 are output simultaneously, perform the troubleshooting for DTC B2785 first.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - MASTER SWITCH)
a.
U165871E02
1.938,4.479 2.083,4.479 2.083,4.479 2.656,3.948 false 1.365,2.073 1.51,2.073 1.51,2.073 2.156,1.521 false 0.24,0.031 2.594,0.354 2.354,0.323 10 false Front view of wire harness connector: (to Certification ECU) 0.26,2.24 2.615,2.563 2.354,0.323 10 false Front view of wire harness connector: (to Main Body ECU) 0.177,0.906 0.531,1.094 0.354,0.188 10 false E29 0.24,3.135 0.5,3.302 0.26,0.167 10 false 2D 1.125,2 1.427,2.188 0.302,0.188 10 false LIN 1.625,4.406 1.969,4.604 0.344,0.198 10 false LIN1

Disconnect the 2D and E29 ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-10 (LIN) - 2D-20 (LIN1) Always Below 1 Ω
E29-10 (LIN) - Body ground Always 10 kΩ or higher



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E29-10 (LIN) - Body ground Always Below 1 V




OK

2.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC
a.

Reconnect the E26 and E29 ECU connectors.


b.

Reconnect the E28 box connector.



d.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

3.CHECK FOR DTC

B

5.REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
3.CHECK FOR DTC
a.

Reconnect the 2D ECU connector.


b.

Disconnect the E26 ECU connector.



d.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

4.CHECK FOR DTC

B

7.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
4.CHECK FOR DTC
a.

Reconnect the E26 ECU connector.


b.

Disconnect the E28 box ECU connector.



d.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
5.REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
a.

Temporarily replace the main body ECU (cowl side junction block LH) with a new or normally functioning one.




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is not output A
DTC B2785 is output B



A

END (MAIN BODY ECU IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Temporarily replace the steering lock ECU with a new or normally functioning one (See page Steering>STEERING COLUMN>MULTIPLEX TILT AND TELESCOPIC ECU>REMOVAL).




NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is not output A
DTC B2785 is output B



A

END (STEERING LOCK ECU IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Temporarily replace the ID code box immobiliser code ECU with a new or normally functioning one.




NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is not output A
DTC B2785 is output B



A

END (ID CODE BOX IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)