The LIN communication of the components related to the rear air conditioning occurs between the air conditioning amplifier, air conditioning control and No. 2 air conditioning control*.
*: w/ Rear heater
When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check air conditioning type.
| Result | Proceed to |
|---|---|
| w/ Rear Heater | A |
| w/o Rear Heater | B |
A
B
Disconnect the E36 amplifier connector
Disconnect the E55 panel connector.
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E36-20 (RLIN) - E55-4 (RLIN) | Always | Below 1 Ω |
| E36-20 (RLIN) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the panel connector.
Measure the resistance and voltage according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E55-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E55-6 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to No. 2 Air Conditioning Control) |
OK
NG
Temporarily replace the No. 2 air conditioning control panel with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING PANEL>REMOVAL).
Check that the rear air conditioning function is normal.
Rear air conditioning function is normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Navigation System) | B |
| NG (w/o Navigation System) | C |
A
B
C
*1: w/ Rear Heater
*2: w/o Rear Heater
*3: w/o Entry and Start System
*4: w/ Entry and Start System
Disconnect the E36*1 E81*2 amplifier connector
Disconnect the F10*3 or F111*4 panel connector.
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E36-21 (LIN1) - F10-5 (LIN1)*3 | Always | Below 1 Ω |
| E36-21 (LIN1) - F111-2 (LIN1)*4 | Always | Below 1 Ω |
| E36-21 (LIN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-37 (LIN1) - F10-5 (LIN1)*3 | Always | Below 1 Ω |
| E81-37 (LIN1) - F111-2 (LIN1)*4 | Always | Below 1 Ω |
| E81-37 (LIN1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the panel connector.
Measure the resistance and voltage according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-8 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F10-7 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F111-5 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | w/o Entry and Start System |
| *B | w/ Entry and Start System |
| *a | Front view of wire harness connector
(to Air Conditioning Control) |
OK
NG
Temporarily replace the air conditioning control with a new or normally functioning one.
w/o Entry and Start System: See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Entry and Start System)>REMOVAL
w/o Navigation System: See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Navigation System)>REMOVAL
Check the that front air conditioning function is normal.
Front air conditioning function is normal.
OK
NG