Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Suspension Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Suspension Control ECU Communication Stop Mode Either Condition is met:
·

Communication stop for "Suspension Control (Air Suspension)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Suspension Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Suspension control ECU CAN branch wire or connector

·

Power source circuit of suspension control ECU

·

Suspension control ECU ground circuit

·

Suspension control ECU



WIRING DIAGRAM

C358555E02
0.219,2.302 2.406,2.604 2.188,0.302 10 false No. 4 CAN Junction Connector 0.219,2.135 0.75,2.333 0.531,0.198 10 false K65 2.219,2.677 3.469,2.979 1.25,0.302 10 false from Battery 1.708,3.5 3.208,3.875 1.5,0.375 10 false from IG1 NO.1 Relay 4,2.521 5.25,2.823 1.25,0.302 10 false AHC-B NO.2 3.99,3.333 5.24,3.635 1.25,0.302 10 false ECU-IG NO.2 5.427,5.156 7.115,5.458 1.688,0.302 10 false Suspension Control ECU 5.417,4.969 6.667,5.167 1.25,0.198 10 false K34 5.656,1.219 6.188,1.417 0.531,0.198 10 false CANH 5.667,1.781 6.198,1.979 0.531,0.198 10 false CANL 5.656,2.688 6.188,2.885 0.531,0.198 10 false BAT2 5.656,3.531 6.188,3.729 0.531,0.198 10 false IG 5.667,4.344 6.198,4.542 0.531,0.198 10 false GND 1.75,1.083 2.281,1.281 0.531,0.198 10 false 1 1.74,1.667 2.271,1.865 0.531,0.198 10 false 2 5.438,1.083 5.969,1.281 0.531,0.198 10 false 7 5.438,1.698 5.969,1.896 0.531,0.198 10 false 8 5.438,2.583 5.969,2.781 0.531,0.198 10 false 3 5.438,3.396 5.969,3.594 0.531,0.198 10 false 5 5.438,4.219 5.969,4.417 0.531,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Drive the vehicle for 10 seconds or more at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
a.
U164989E02
2.396,1.427 2.521,1.854 2.521,1.854 2.615,1.854 false 2.729,1.604 2.646,1.604 2.646,1.604 2.469,1.417 false 0.052,0.042 0.323,0.271 0.271,0.229 10 false *a 2.646,1.76 3.135,1.958 0.49,0.198 10 false CANL 2.781,1.521 3.323,1.708 0.542,0.188 10 false CANH 1.01,1.344 1.365,1.542 0.354,0.198 10 false K34

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-7 (CANH) - K37-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)
a.
U164988E02
2.177,1.229 2.542,0.844 2.542,0.844 2.625,0.844 false 1.531,1.031 1.615,1.031 1.615,1.031 1.875,1.229 false 2.719,1.083 2.635,1.083 2.635,1.083 2.427,1.229 false 0.052,0.021 0.365,0.229 0.313,0.208 10 false *a 2.667,0.76 3.115,0.927 0.448,0.167 10 false BAT2 2.771,1 3.219,1.167 0.448,0.167 10 false GND 1.313,0.948 1.76,1.115 0.448,0.167 10 false IG 1.01,1.344 1.365,1.563 0.354,0.219 10 false K34

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K34-3 (BAT2) - Body ground Always 11 to 14 V
K34-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)


OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR