Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › 2015.08–2020.06
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either Condition is met:
·

Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Air conditioning amplifier assembly CAN branch wire or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C339023E05
0.514,1.335 2.484,1.722 1.971,0.387 10 E135 1.695,0.872 1.934,1.151 0.239,0.278 10 18 1.709,0.354 1.962,0.660 0.253,0.306 10 8 5.305,0.251 5.679,0.639 0.373,0.387 10 3 5.235,0.466 5.609,0.853 0.373,0.387 10 E35 5.66,0.466 6.242,0.742 0.582,0.276 10 CANH 5.305,0.77 5.679,1.157 0.373,0.387 10 4 5.235,0.995 5.609,1.383 0.373,0.387 10 E35 5.66,0.984 6.242,1.261 0.582,0.276 10 CANL 5.277,3.138 5.651,3.525 0.373,0.387 10 5 5.235,3.352 5.609,3.740 0.373,0.387 10 E36 5.66,3.352 6.242,3.629 0.582,0.276 10 IG+ 5.319,4.243 5.693,4.631 0.373,0.387 10 1 5.235,4.458 5.609,4.846 0.373,0.387 10 E36 5.66,4.458 6.242,4.735 0.582,0.276 10 GND 5.319,3.664 5.693,4.052 0.373,0.387 10 6 5.235,3.879 5.609,4.267 0.373,0.387 10 E35 5.66,3.879 6.242,4.156 0.582,0.276 10 E1 5.319,1.989 5.693,2.376 0.373,0.387 10 6 5.235,2.218 5.609,2.606 0.373,0.387 10 E36 5.66,2.203 6.242,2.480 0.582,0.276 10 +B1 5.319,2.518 5.693,2.905 0.373,0.387 10 7 5.235,2.733 5.609,2.888 0.373,0.155 10 E36 5.66,2.733 6.242,3.009 0.582,0.276 10 +B2 0.514,1.503 2.484,1.890 1.971,0.387 10 No. 1 CAN Junction Connector 3.734,2.068 4.569,2.223 0.835,0.155 10 A/C 1.617,2.204 2.452,2.360 0.835,0.155 10 from Battery 3.482,3.22 4.187,3.376 0.706,0.155 10 A/C COMP 1.439,3.357 2.779,3.512 1.340,0.155 10 from IG1 Relay 5.319,5.175 6.896,5.497 1.577,0.323 10 Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 15 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
U156284E04
1.854,0.833 2.24,0.552 2.24,0.552 2.438,0.552 false 1.75,0.833 2.146,0.167 2.146,0.167 2.344,0.167 false 2.385,0.073 2.938,0.271 0.552,0.198 10 false CANL 2.5,0.469 3.083,0.667 0.583,0.198 10 false CANH 0.573,0.979 0.948,1.208 0.375,0.229 10 false E35 0.115,0.063 0.531,0.208 0.417,0.146 10 false *a

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-3 (CANH) - E35-4 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165658E02
2.125,3.208 2.323,3.104 2.323,3.104 2.438,3.104 false 1.313,3.208 1.115,3.104 1.115,3.104 1,3.104 false 0.906,2.844 1.167,2.844 1.167,2.844 1.417,3.198 false 1.552,3.208 1.219,2.583 1.219,2.583 1.083,2.583 false 1.365,1.063 1.156,0.958 1.156,0.958 1.052,0.958 false 0.104,0.052 0.521,0.25 0.417,0.198 10 false *a 0.51,3.323 0.885,3.563 0.375,0.24 10 false E36 2.479,3.021 2.958,3.229 0.479,0.208 10 false GND 0.667,3.031 1.135,3.229 0.469,0.198 10 false +B2 0.573,2.771 0.99,2.958 0.417,0.188 10 false +B1 0.792,2.5 1.24,2.688 0.448,0.188 10 false IG+ 2.667,1.208 3.073,1.406 0.406,0.198 10 false E35 0.802,0.885 1.167,1.073 0.365,0.188 10 false E1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E36-6 (+B1) - Body ground Always 11 to 14 V
E36-7 (+B2) - Body ground Always 11 to 14 V
E36-5 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-6 (E1) - Body ground Always Below 1 Ω
E36-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR