Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  U0199  Lost Communication with "Door Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0199 There is no communication from the outer mirror control ECU assembly LH.
·

Outer mirror control ECU assembly LH CAN branch wire or connector

·

Power source or inside of outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly LH ground circuit

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

C358556E01
0.354,2.271 2.5,2.583 2.146,0.313 10 false No. 7 CAN Junction Connector 0.354,2.104 1.177,2.313 0.823,0.208 10 false E134 1.708,3.813 3.354,4.104 1.646,0.292 10 false from IG1 NO.2 Relay 2.188,3.208 3.365,3.5 1.177,0.292 10 false from Battery 2.188,2.625 3.365,2.917 1.177,0.292 10 false from Battery 4.01,2.458 5.188,2.75 1.177,0.292 10 false MPX-B NO.1 4.063,3.031 5.208,3.323 1.146,0.292 10 false DOOR F/P 3.99,3.635 5.167,3.927 1.177,0.292 10 false ECU-IG NO.3 5.49,5.115 7,5.625 1.51,0.51 10 false Outer Mirror Control ECU Assembly LH 5.49,4.948 6.063,5.188 0.573,0.24 10 false I41 5.667,1.167 6.281,1.365 0.615,0.198 10 false CANP 5.667,1.771 6.281,1.969 0.615,0.198 10 false CANN 5.667,2.625 6.281,2.823 0.615,0.198 10 false CPUB 5.667,3.24 6.281,3.438 0.615,0.198 10 false BDR 5.667,3.823 6.281,4.021 0.615,0.198 10 false SIG 5.677,4.323 6.292,4.521 0.615,0.198 10 false GND 1.729,1.656 2.042,1.854 0.313,0.198 10 false 14 1.729,1.073 2.042,1.271 0.313,0.198 10 false 3 5.375,3.115 5.688,3.313 0.313,0.198 10 false 14 5.438,2.51 5.75,2.708 0.313,0.198 10 false 6 5.438,1.656 5.75,1.854 0.313,0.198 10 false 8 5.438,1.073 5.75,1.271 0.313,0.198 10 false 9 5.448,3.708 5.76,3.906 0.313,0.198 10 false 5 5.448,4.219 5.76,4.417 0.313,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.


Result
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU). A
DTC U1002 is output from main body ECU (multiplex network body ECU). B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY LH CAN BRANCH WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY LH CAN BRANCH WIRE)
a.
U165529E01
1.304,1.259 1.073,1.463 1.073,1.463 0.888,1.463 false 1.155,1.814 1.387,1.814 1.387,1.814 1.436,1.259 false 0.635,1.725 1.131,1.888 0.496,0.163 10 CANP 0.368,1.373 0.864,1.535 0.496,0.163 10 CANN 0.106,0.075 0.602,0.238 0.496,0.163 10 *a 2.742,0.883 2.960,1.021 0.218,0.139 10 I41

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I41-9 (CANP) - I41-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)



OK

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY LH (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
U165530E02
2.229,0.948 2.458,0.74 2.458,0.74 2.646,0.74 false 2.51,0.448 2.281,0.448 2.281,0.448 2.031,0.979 false 1.885,0.979 2.021,0.188 2.021,0.188 2.156,0.188 false 2.198,1.25 2.438,1.49 2.438,1.49 2.656,1.49 false 2.708,1.385 3.25,1.594 0.542,0.208 10 false BDR 2.698,0.646 3.292,0.854 0.594,0.208 10 false GND 2.563,0.354 3.146,0.563 0.583,0.208 10 false CPUB 2.208,0.094 2.792,0.271 0.583,0.177 10 false SIG 0.104,0.073 0.604,0.24 0.5,0.167 10 false *a 0.51,0.896 0.875,1.104 0.365,0.208 10 false I41

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I41-6 (CPUB) - Body ground Always 11 to 14 V
I41-14 (BDR) - Body ground Always 11 to 14 V
I41-5 (SIG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I41-7 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR