The driving support ECU assembly will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to local bus.
When the driving support ECU assembly receives a response signal from the ECUs connected to local bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to local bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to local bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to local bus, the driving support ECU assembly determines that a malfunction exists.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| U1002 | Driving support ECU assembly cannot receive signals from all ECUs that have been memorized as those connected to local bus. | ·
Open or short in local bus CAN main wire or connector ·
Open or short in local bus CAN branch wire or connector ·
Driving support ECU assembly ·
Millimeter wave radar sensor assembly ·
Forward recognition camera ·
No. 10 CAN junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 6 seconds.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Resistance: Malfunction |
|---|---|---|---|
| E164-8 (CA1P) - E164-9 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 53 Ω: Short in line |
| E164-8 (CA1P) - E164-9 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Higher than 70 Ω: Open in CAN main bus line |
| E164-8 (CA1P) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: +B short |
| E164-9 (CA1N) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: +B short |
| E164-8 (CA1P) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Ground short |
| E164-9 (CA1N) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Ground short |
| *a | Component with harness connected
(Driving Support ECU Assembly) |
| *B | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus wire) | B |
| NG (Short circuit between bus wire) | C |
| NG
·
Ground short ·
+B short |
D |
A
B
C
D
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Recheck for DTCs and check that no DTCs are output (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
DTC U1002 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R20-6 (CANH) - R20-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
OK
NG
Reconnect the R20 forward recognition camera connector.
NEXT
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A72-5 (CA1P) - A72-6 (CA1N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
OK
NG
Reconnect the A72 millimeter wave radar sensor assembly connector.
NEXT
Disconnect the No. 10 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 10 CAN Junction Connector) |
*b | to Millimeter Wave Radar Sensor Assembly |
| *c | to Forward Recognition Camera | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E174-5 (CANH) - E174-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Millimeter wave radar sensor assembly |
| E174-6 (CANH) - E174-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Forward recognition camera |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Millimeter wave radar sensor assembly CAN main wire) | B |
| NG (Forward recognition camera CAN main wire) | C |
A
B
C
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R20-6 (CANH) - R20-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
OK
NG
Reconnect the R20 forward recognition camera connector.
NEXT
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A72-5 (CA1P) - A72-6 (CA1N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
OK
NG
Reconnect the A72 millimeter wave radar sensor assembly connector.
NEXT
Disconnect the No. 10 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 10 CAN Junction Connector) |
*b | to Millimeter Wave Radar Sensor Assembly |
| *c | to Forward Recognition Camera | *d | to Driving Support ECU Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E174-5 (CANH) - E174-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Millimeter wave radar sensor assembly |
| E174-6 (CANH) - E174-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Forward recognition camera |
| E174-7 (CANH) - E174-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Driving support ECU assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Millimeter wave radar sensor assembly CAN main wire) | B |
| NG (Forward recognition camera CAN main wire) | C |
| NG (Driving support ECU assembly CAN branch wire) | D |
A
B
C
D
Reconnect the E174 No. 10 CAN junction connector.
NEXT
Disconnect the driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E164-8 (CA1P) - E164-9 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Driving Support ECU Assembly) |
OK
NG
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R20-6 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R20-12 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R20-6 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R20-12 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the R20 forward recognition camera connector.
NEXT
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A72-5 (CA1P) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A72-6 (CA1N) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A72-5 (CA1P) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A72-6 (CA1N) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A72 millimeter wave radar sensor assembly connector.
NEXT
Disconnect the No. 10 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 10 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Millimeter Wave Radar Sensor Assembly | *d | to Forward Recognition Camera |
| *e | to Driving Support ECU Assembly | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E174-5 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Millimeter wave radar sensor assembly |
| E174-15 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E174-5 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E174-15 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E174-6 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Forward recognition camera |
| E174-16 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E174-6 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E174-16 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E174-7 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Driving support ECU assembly |
| E174-17 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E174-7 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E174-17 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Millimeter wave radar sensor assembly CAN main wire) | B |
| NG (Driving support ECU assembly CAN main wire) | C |
| NG (Forward recognition camera CAN branch wire) | D |
A
B
C
D
Reconnect the E174 No. 10 CAN junction connector.
NEXT
Disconnect the driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E164-8 (CA1P) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E164-9 (CA1N) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E164-8 (CA1P) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E164-9 (CA1N) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Driving Support ECU Assembly) |
| *b | Front view of DLC3 |
OK
NG