Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Either Condition is met:
·

Communication stop for "Panoramic View Monitor" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Parking Assist ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Parking assist ECU CAN branch wire or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



WIRING DIAGRAM

C306930E08
5.646,1 6.104,1.208 0.458,0.208 10 false CANH 5.635,1.521 6.125,1.781 0.49,0.26 10 false CANL 5.656,2.365 6.01,2.656 0.354,0.292 10 false +B 5.677,3.844 6.146,4.073 0.469,0.229 10 false ACC 5.667,3.125 6,3.344 0.333,0.219 10 false IG 5.646,4.385 6.052,4.635 0.406,0.25 10 false GND1 5.271,1.01 5.781,1.365 0.51,0.354 10 false F76 5.271,1.521 5.75,1.854 0.479,0.333 10 false F76 5.281,2.375 5.646,2.583 0.365,0.208 10 false F75 5.302,0.802 5.542,0.958 0.24,0.156 10 false 40 5.313,1.323 5.552,1.479 0.24,0.156 10 false 39 5.344,2.156 5.583,2.313 0.24,0.156 10 false 1 5.333,2.917 5.469,3.094 0.135,0.177 10 false 8 5.344,3.646 5.458,3.813 0.115,0.167 10 false 9 5.344,4.188 5.583,4.344 0.24,0.156 10 false 4 1.542,0.906 1.781,1.063 0.24,0.156 10 false 8 1.521,1.427 1.76,1.583 0.24,0.156 10 false 18 0.292,1.896 0.76,2.24 0.469,0.344 10 false E151 0.281,2.052 2.156,2.24 1.875,0.188 10 false No. 3 CAN Junction Connector 2.292,2.365 3.073,2.583 0.781,0.219 10 false from Battery 1.75,3.125 3.104,3.313 1.354,0.188 10 false from IG1 NO.4 Relay 5.365,4.917 6.635,5.125 1.271,0.208 10 false Parking Assist ECU 2,3.854 3.042,4.063 1.042,0.208 10 false from ACC Relay 3.958,2.229 4.948,2.49 0.99,0.26 10 false MPX-B NO.1 3.875,2.948 4.854,3.146 0.979,0.198 10 false ECU-IG NO.6 4.042,3.719 4.875,3.917 0.833,0.198 10 false ECU-ACC 5.271,3.125 5.635,3.333 0.365,0.208 10 false F75 5.271,4.396 5.635,4.604 0.365,0.208 10 false F75 5.271,3.865 5.635,4.073 0.365,0.208 10 false F75

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 13 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU CAN BRANCH WIRE)
a.
U165541E01
0.109,0.08 0.515,0.407 0.406,0.327 10 *a 1.628,0.318 1.892,0.455 0.264,0.136 10 F76 1.037,1.241 0.834,1.444 0.834,1.444 0.561,1.444 false 0.785,1.727 0.962,1.727 0.962,1.727 1.099,1.241 false 0.03,1.361 0.460,1.497 0.430,0.136 10 CANH 0.27,1.644 0.701,1.781 0.430,0.136 10 CANL

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-40 (CANH) - F76-39 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)



OK

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING ASSIST ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U165548E01
0.109,0.08 0.515,0.407 0.406,0.327 10 *a 1.628,0.267 1.892,0.403 0.264,0.136 10 F75 1.984,1.286 2.187,1.489 2.187,1.489 2.46,1.489 false 2.236,1.772 2.059,1.772 2.059,1.772 1.922,1.286 false 2.258,1.693 2.689,1.830 0.430,0.136 10 ACC 0.287,0.819 0.718,0.956 0.430,0.136 10 GND1 1.267,1.103 1.064,0.899 1.064,0.899 0.792,0.899 false 2.237,1.103 2.44,0.899 2.44,0.899 2.712,0.899 false 2.737,0.828 3.167,0.964 0.430,0.136 10 +B 2.476,1.404 2.906,1.540 0.430,0.136 10 IG

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the parking assist ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F75-1 (+B) - Body ground Always 11 to 14 V
F75-8 (IG) - Body ground Ignition switch ON 11 to 14 V
F75-9 (ACC) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-4 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR