| Detection Item | Symptom | Trouble Area |
|---|---|---|
| ECM Communication Stop Mode | Either Condition is met:
|
·
ECM CAN main wire or connector ·
Power source circuit of ECM ·
ECM ground circuit ·
ECM |
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
for 1UR-FE, 1GR-FE:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-10 (CANH) - A38-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
for 1VD-FTV:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-41 (CANH) - A38-49 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
for 3UR-FE:
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-11 (CANH) - A38-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
for 1UR-FE, 1GR-FE:
Connect the cable to the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-1 (BATT) - Body ground | Always | 11 to 14 V |
| A38-3 (+B) - Body ground | Battery positive (+) voltage applied to terminal A38-34 (MREL) | 11 to 14 V |
| A38-2 (+B2) - Body ground | Battery positive (+) voltage applied to terminal A38-34 (MREL) | 11 to 14 V |
| A38-28 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-31 (EC) - Body ground | Always | Below 1 Ω |
| C45-42 (E02) - Body ground | Always | Below 1 Ω |
| C45-43 (E01) - Body ground | Always | Below 1 Ω |
| C45-82 (ME01) - Body ground | Always | Below 1 Ω |
| C45-81 (E1) - Body ground | Always | Below 1 Ω |
| C45-23 (E04) - Body ground | Always | Below 1 Ω |
| C45-21 (E05) - Body ground | Always | Below 1 Ω |
for 1VD-FTV:
Connect the cable to the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-20 (BATT) - Body ground | Always | 11 to 14 V |
| A38-2 (+B) - Body ground | Battery positive (+) voltage applied to terminal A38-44 (MREL) | 11 to 14 V |
| A38-1 (+B2) - Body ground | Battery positive (+) voltage applied to terminal A38-44 (MREL) | 11 to 14 V |
| A38-28 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-32 (EC) - Body ground | Always | Below 1 Ω |
| C45-21 (E02) - Body ground | Always | Below 1 Ω |
| C45-22 (E01) - Body ground | Always | Below 1 Ω |
| C45-81 (E1) - Body ground | Always | Below 1 Ω |
| C45-44 (E04) - Body ground | Always | Below 1 Ω |
| C45-23 (E05) - Body ground | Always | Below 1 Ω |
for 3UR-FE:
Connect the cable to the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-1 (BATT) - Body ground | Always | 11 to 14 V |
| A38-2 (+B) - Body ground | Battery positive (+) voltage applied to terminal A38-6 (MREL) | 11 to 14 V |
| A38-3 (+B2) - Body ground | Battery positive (+) voltage applied to terminal A38-6 (MREL) | 11 to 14 V |
| A38-4 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-52 (EC) - Body ground | Always | Below 1 Ω |
| C45-43 (E02) - Body ground | Always | Below 1 Ω |
| C45-41 (E01) - Body ground | Always | Below 1 Ω |
| C45-18 (ME01) - Body ground | Always | Below 1 Ω |
| C45-81 (E1) - Body ground | Always | Below 1 Ω |
| C45-23 (E04) - Body ground | Always | Below 1 Ω |
| C45-46 (E05) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for 1UR-FE) | A |
| OK (for 1VD-FTV) | B |
| OK (for 1GR-FE) | C |
| OK (for 3UR-FE) | D |
| NG | E |
A
B
C
D
E