Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either Condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the "Bus Check" screen (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Radio and display receiver assembly CAN branch wire or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C280381E47
5.104,5.979 7.073,6.688 1.969,0.708 10 false Radio and Display Receiver Assembly 5.646,5.073 7,5.458 1.354,0.385 10 false GND1 5.646,4.24 7,4.625 1.354,0.385 10 false IG 5.635,2.615 6.99,3 1.354,0.385 10 false +B1 5.615,3.396 6.969,3.781 1.354,0.385 10 false ACC1 5.646,1.438 7,1.823 1.354,0.385 10 false CANL 5.656,0.833 7.01,1.219 1.354,0.385 10 false CANH 1.677,0.698 3.031,1.083 1.354,0.385 10 false 10 1.667,1.271 3.021,1.656 1.354,0.385 10 false 21 0.427,1.771 1.781,2.156 1.354,0.385 10 false E152 0.438,1.938 2.813,2.219 2.375,0.281 10 false No. 5 CAN Junction Connector 2.104,2.573 3.458,2.958 1.354,0.385 10 false from Battery 1.604,4.219 2.958,4.604 1.354,0.385 10 false from IG1 NO.2 Relay 1.854,3.385 3.208,3.771 1.354,0.385 10 false from ACC Relay 3.958,3.24 5.458,3.635 1.5,0.396 10 false ECU-ACC 3.833,4.052 5.188,4.438 1.354,0.385 10 false ECU-IG NO.3 4.042,2.417 4.958,2.833 0.917,0.417 10 false RADIO 5.104,2.594 6.021,3.01 0.917,0.417 10 false F120 5.104,3.427 6.021,3.844 0.917,0.417 10 false F120 5.115,4.24 6.031,4.656 0.917,0.417 10 false F124 5.115,5.052 6.031,5.469 0.917,0.417 10 false F120 5.104,1.417 6.021,1.833 0.917,0.417 10 false F124 5.115,0.823 6.031,1.24 0.917,0.417 10 false F124 5.188,1.146 6.542,1.531 1.354,0.385 10 false 10 5.24,0.563 6.594,0.948 1.354,0.385 10 false 9 5.24,3.188 5.521,3.479 0.281,0.292 10 false 3 5.229,2.354 6.583,2.74 1.354,0.385 10 false 4 5.219,3.99 6.573,4.375 1.354,0.385 10 false 1 5.229,4.781 6.583,5.167 1.354,0.385 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U165124E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.546,0.371 1.931,0.512 0.385,0.140 10 F124 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-9 (CANH) - F124-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165438E01
0.064,0.06 0.269,0.230 0.205,0.170 10 *a 2.01,0.866 2.297,0.554 2.297,0.554 2.402,0.554 false 2.184,0.98 2.383,1.19 2.383,1.19 2.488,1.19 false 1.599,1.152 1.351,1.459 1.351,1.459 1.246,1.459 false 0.449,2.359 0.613,2.498 0.165,0.139 10 IG 0.743,1.384 1.154,1.522 0.411,0.139 10 GND1 2.505,1.113 2.916,1.251 0.411,0.139 10 +B1 2.423,0.477 2.835,0.615 0.411,0.139 10 ACC1 0.651,2.432 0.786,2.432 0.786,2.432 0.981,2.605 false 1.526,1.826 1.902,1.963 0.376,0.137 10 F124 1.54,0.256 1.923,0.393 0.383,0.137 10 F120

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F120-4 (+B1) - Body ground Always 11 to 14 V
F120-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F124-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F120-7 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR