Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either Condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Bus Check" screen (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Master cylinder solenoid (skid control ECU) CAN branch wire or connector

·

Power source circuit of master cylinder solenoid (skid control ECU)

·

Master cylinder solenoid (skid control ECU) ground circuit

·

Master cylinder solenoid (skid control ECU)



WIRING DIAGRAM

C339021E02
0.488,1.403 2.458,1.790 1.971,0.387 10 E133 1.683,0.968 3.654,1.356 1.971,0.387 10 13 1.683,0.45 3.654,0.837 1.971,0.387 10 3 5.251,0.319 5.625,0.707 0.373,0.387 10 11 5.209,0.534 5.583,0.922 0.373,0.387 10 A24 5.634,0.534 6.216,0.810 0.582,0.276 10 CANH 5.251,0.838 5.625,1.225 0.373,0.387 10 25 5.209,1.063 5.583,1.451 0.373,0.387 10 A24 5.634,1.053 6.216,1.329 0.582,0.276 10 CANL 5.251,3.128 5.625,3.516 0.373,0.387 10 31 5.209,3.343 5.583,3.731 0.373,0.387 10 A24 5.634,3.343 6.216,3.620 0.582,0.276 10 +BS 5.251,3.81 5.625,4.198 0.373,0.387 10 46 5.209,4.025 5.583,4.412 0.373,0.387 10 A24 5.634,4.025 6.216,4.301 0.582,0.276 10 IG1 5.293,6.183 5.667,6.570 0.373,0.387 10 4 5.209,6.397 5.583,6.785 0.373,0.387 10 A25 5.634,6.397 6.216,6.674 0.582,0.276 10 GND3 5.293,5.076 5.667,5.463 0.373,0.387 10 1 5.209,5.291 5.583,5.678 0.373,0.387 10 A24 5.634,5.291 6.216,5.567 0.582,0.276 10 GND1 5.251,5.604 5.625,5.991 0.373,0.387 10 32 5.209,5.818 5.583,6.206 0.373,0.387 10 A24 5.634,5.818 6.216,6.095 0.582,0.276 10 GND2 5.293,2.057 5.667,2.444 0.373,0.387 10 2 5.209,2.287 5.583,2.674 0.373,0.387 10 A24 5.634,2.271 6.216,2.548 0.582,0.276 10 +BM1 5.293,2.586 5.667,2.973 0.373,0.387 10 2 5.209,2.801 5.583,2.956 0.373,0.155 10 A25 5.634,2.801 6.216,3.077 0.582,0.276 10 +BM2 5.293,4.449 5.667,4.837 0.373,0.387 10 1 5.209,4.664 5.583,4.820 0.373,0.155 10 A25 5.634,4.664 6.216,4.940 0.582,0.276 10 IG2 0.488,1.557 2.458,1.944 1.971,0.387 10 No. 1 CAN Junction Connector 3.507,2.136 4.342,2.291 0.835,0.155 10 ABS NO.1 1.591,2.272 2.426,2.428 0.835,0.155 10 from Battery 3.507,3.197 4.342,3.352 0.835,0.155 10 ABS NO.2 1.591,3.334 2.426,3.489 0.835,0.155 10 from Battery 3.372,3.893 4.276,4.048 0.905,0.155 10 ECU-IG NO.1 1.082,4.029 2.422,4.185 1.340,0.155 10 from IG1 NO.3 Relay 3.554,4.54 4.458,4.695 0.905,0.155 10 IG2 NO.1 1.082,4.677 2.422,4.832 1.340,0.155 10 from IG2 MAIN Relay 5.291,7.083 6.868,7.406 1.577,0.323 10 Master Cylinder Solenoid (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U156451E01
0.1,0.106 0.286,0.278 0.185,0.172 10 *a 1.014,0.315 1.287,0.452 0.272,0.137 10 A24 2.56,0.23 3.065,0.366 0.505,0.137 10 CANH 2.638,0.556 3.142,0.693 0.505,0.137 10 CANL 2.178,1.099 2.464,0.626 2.464,0.626 2.605,0.626 false 2.519,0.312 2.343,0.312 2.343,0.312 2.143,1.014 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the master cylinder solenoid (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-11 (CANH) - A24-25 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C329397E04
1.49,0.177 2.083,0.5 0.594,0.323 1.479,2.344 2.073,2.667 0.594,0.323 0.771,1.031 0.542,0.854 0.542,0.854 0.458,0.854 false 0.729,0.594 0.854,0.594 0.854,0.594 1.052,1.021 false 0.854,1.365 0.646,1.635 0.646,1.635 0.5,1.635 false 0.719,1.917 0.885,1.917 0.885,1.917 1.073,1.365 false 1.917,3.26 2.469,2.969 2.469,2.969 2.604,2.969 false 2.677,1.406 2.885,1.781 2.885,1.781 3.021,1.781 false 1.469,3.271 1.125,2.99 1.125,2.99 0.99,2.99 false 1.938,3.771 2.281,3.969 2.281,3.969 2.49,3.969 false 0.135,0.094 0.479,0.302 0.344,0.208 10 false *a 1.667,0.26 2.083,0.458 0.417,0.198 10 false A24 1.656,2.427 2.052,2.615 0.396,0.188 10 false A25 3.052,1.708 3.406,1.969 0.354,0.26 10 false IG1 0.271,1.833 0.823,2.031 0.552,0.198 10 false GND2 0.052,0.771 0.583,0.958 0.531,0.188 10 false GND1 0.292,0.5 0.76,0.708 0.469,0.208 10 false +BM1 2.646,2.885 3.198,3.073 0.552,0.188 10 false +BM2 0.115,1.563 0.573,1.74 0.458,0.177 10 false +BS 0.698,2.917 1.125,3.104 0.427,0.188 10 false IG2 2.531,3.885 3.135,4.083 0.604,0.198 10 false GND3

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the master cylinder solenoid (skid control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 (+BM1) - Body ground Always 11 to 14 V
A24-31 (+BS) - Body ground Always 11 to 14 V
A25-2 (+BM2) - Body ground Always 11 to 14 V
A24-46 (IG1) - Body ground Ignition switch ON 11 to 14 V
A25-1 (IG2) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (GND1) - Body ground Always Below 1 Ω
A24-32 (GND2) - Body ground Always Below 1 Ω
A25-4 (GND3) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR