Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either Condition is met:
·

"Air Conditioning Amplifier" is not displayed on the "Bus Check" screen (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Air conditioning amplifier assembly CAN branch wire or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C344597E04
0.472,2.063 2.442,2.451 1.971,0.387 10 E133 1.667,1.629 3.638,2.016 1.971,0.387 10 16 1.667,1.111 3.638,1.498 1.971,0.387 10 6 5.193,1.195 5.567,1.582 0.373,0.387 10 E35 5.618,1.195 6.200,1.471 0.582,0.276 10 CANH 5.193,1.724 5.567,2.111 0.373,0.387 10 E35 5.618,1.713 6.200,1.989 0.582,0.276 10 CANL 5.193,4.081 5.567,4.468 0.373,0.387 10 E36 5.618,4.081 6.200,4.357 0.582,0.276 10 IG+ 5.277,4.972 5.651,5.359 0.373,0.387 10 1 5.193,5.187 5.567,5.574 0.373,0.387 10 E36 5.618,5.187 6.200,5.463 0.582,0.276 10 GND 5.277,4.393 5.651,4.780 0.373,0.387 10 6 5.277,3.866 5.651,4.253 0.373,0.387 10 5 5.193,4.608 5.567,4.995 0.373,0.387 10 E35 5.618,4.608 6.200,4.884 0.582,0.276 10 E1 5.277,2.717 5.651,3.104 0.373,0.387 10 6 5.277,1.498 5.651,1.886 0.373,0.387 10 4 5.277,0.98 5.651,1.367 0.373,0.387 10 3 5.193,2.947 5.567,3.334 0.373,0.387 10 E36 5.618,2.932 6.200,3.208 0.582,0.276 10 +B1 5.277,3.246 5.651,3.634 0.373,0.387 10 7 5.193,3.461 5.567,3.617 0.373,0.155 10 E36 5.618,3.461 6.200,3.738 0.582,0.276 10 +B2 0.472,2.217 2.442,2.605 1.971,0.387 10 No. 1 CAN Junction Connector 0.22,0.116 5.718,0.503 5.498,0.387 12 for Automatic Air Conditioning System: 3.692,2.796 4.527,2.952 0.835,0.155 10 A/C 1.575,2.933 2.410,3.088 0.835,0.155 10 from Battery 3.44,3.949 4.145,4.104 0.706,0.155 10 A/C COMP 1.397,4.085 2.737,4.241 1.340,0.155 10 from IG1 Relay 5.277,5.903 6.854,6.226 1.577,0.323 10 Air Conditioning Amplifier Assembly

C344598E04
5.281,4.802 6.909,4.949 1.628,0.147 10 E81 5.316,4.086 6.080,4.232 0.764,0.147 10 14 5.386,3.253 6.150,3.399 0.764,0.147 10 1 5.316,2.427 6.080,2.573 0.764,0.147 10 21 5.618,4.177 6.381,4.323 0.764,0.147 10 GND 5.618,3.344 6.381,3.490 0.764,0.147 10 IG+ 5.618,2.518 6.381,2.664 0.764,0.147 10 +B1 5.618,1.617 6.381,1.764 0.764,0.147 10 CANL 5.618,1.029 6.381,1.176 0.764,0.147 10 CANH 5.316,1.498 6.080,1.644 0.764,0.147 10 12 5.316,0.938 6.080,1.084 0.764,0.147 10 11 5.281,4.946 6.858,5.268 1.577,0.323 10 Air Conditioning Amplifier Assembly 0.345,1.946 2.316,2.334 1.971,0.387 10 E133 1.639,1.498 3.609,1.885 1.971,0.387 10 16 1.639,0.938 3.609,1.325 1.971,0.387 10 6 0.345,2.1 2.316,2.488 1.971,0.387 10 No. 1 CAN Junction Connector 0.153,0.095 5.652,0.482 5.498,0.387 12 for Manual Air Conditioning System: 4.174,2.371 5.010,2.527 0.835,0.155 10 A/C 2.226,2.494 3.061,2.649 0.835,0.155 10 from Battery 3.992,3.159 4.698,3.315 0.706,0.155 10 A/C COMP 2.048,3.324 3.388,3.480 1.340,0.155 10 from IG1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U156284E04
1.854,0.833 2.24,0.552 2.24,0.552 2.438,0.552 false 1.75,0.833 2.146,0.167 2.146,0.167 2.344,0.167 false 2.385,0.073 2.938,0.271 0.552,0.198 10 false CANL 2.5,0.469 3.083,0.667 0.583,0.198 10 false CANH 0.573,0.979 0.948,1.208 0.375,0.229 10 false E35 0.115,0.063 0.531,0.208 0.417,0.146 10 false *a

for Automatic Air Conditioning System:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-3 (CANH) - E35-4 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



c.
U165135E01
0.897,0.166 1.316,0.304 0.419,0.137 10 CANH 0.074,0.062 0.262,0.199 0.188,0.137 10 *a 0.536,0.433 0.945,0.570 0.409,0.137 10 CANL 1.642,1.105 1.133,0.499 1.133,0.499 1.006,0.499 false 1.726,1.105 1.584,0.248 1.584,0.248 1.405,0.248 false 2.413,0.256 2.678,0.397 0.265,0.141 10 E81

for Manual Air Conditioning System:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-11 (CANH) - E81-12 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.
U165658E02
2.125,3.208 2.323,3.104 2.323,3.104 2.438,3.104 false 1.313,3.208 1.115,3.104 1.115,3.104 1,3.104 false 0.906,2.844 1.167,2.844 1.167,2.844 1.417,3.198 false 1.552,3.208 1.219,2.583 1.219,2.583 1.083,2.583 false 1.365,1.063 1.156,0.958 1.156,0.958 1.052,0.958 false 0.104,0.052 0.521,0.25 0.417,0.198 10 false *a 0.51,3.323 0.885,3.563 0.375,0.24 10 false E36 2.479,3.021 2.958,3.229 0.479,0.208 10 false GND 0.667,3.031 1.135,3.229 0.469,0.198 10 false +B2 0.573,2.771 0.99,2.958 0.417,0.188 10 false +B1 0.792,2.5 1.24,2.688 0.448,0.188 10 false IG+ 2.667,1.208 3.073,1.406 0.406,0.198 10 false E35 0.802,0.885 1.167,1.073 0.365,0.188 10 false E1

for Automatic Air Conditioning System:

i.

Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E36-6 (+B1) - Body ground Always 11 to 14 V
E36-7 (+B2) - Body ground Always 11 to 14 V
E36-5 (IG+) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-6 (E1) - Body ground Always Below 1 Ω
E36-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



c.
U165134E01
0.074,0.061 0.262,0.198 0.188,0.137 10 *a 2.885,1.372 3.171,1.510 0.287,0.137 10 +B1 2.885,0.825 3.171,0.963 0.287,0.137 10 IG+ 2.567,1.103 2.732,0.912 2.732,0.912 2.86,0.912 false 2.567,1.264 2.732,1.454 2.732,1.454 2.86,1.454 false 0.433,0.552 0.842,0.690 0.409,0.137 10 GND 1.48,1.112 0.976,0.634 0.976,0.634 0.848,0.634 false 1.644,0.249 1.914,0.390 0.269,0.141 10 E81

for Manual Air Conditioning System:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E81-21 (+B1) - Body ground Always 11 to 14 V
E81-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-14 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR