Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the power seat switch assembly.
·

Power seat switch assembly CAN branch wire or connector

·

Power source or inside of power seat switch assembly

·

Power seat switch assembly ground circuit

·

Power seat switch assembly



WIRING DIAGRAM

C339025E08
0.583,1.844 2.563,2.104 1.979,0.26 10 false E136 1.708,1.385 1.927,1.646 0.219,0.26 10 false 15 1.708,0.844 1.927,1.104 0.219,0.26 10 false 4 0.583,2.01 2.771,2.385 2.188,0.375 10 false No. 8 CAN Junction Connector 5.25,0.969 5.646,1.219 0.396,0.25 10 false c47 5.677,0.969 6.344,1.177 0.667,0.208 10 false MPX1 5.323,0.76 5.542,1.021 0.219,0.26 10 false 8 5.25,1.5 5.667,1.74 0.417,0.24 10 false c47 5.677,1.49 6.302,1.75 0.625,0.26 10 false MPX2 5.323,1.281 5.542,1.542 0.219,0.26 10 false 7 5.25,4.198 5.615,4.417 0.365,0.219 10 false c46 5.677,4.198 6.323,4.396 0.646,0.198 10 false GND 5.323,3.979 5.542,4.24 0.219,0.26 10 false 1 5.25,2.906 5.615,3.146 0.365,0.24 10 false c46 5.677,2.885 6.323,3.083 0.646,0.198 10 false +B2 5.323,2.688 5.542,2.948 0.219,0.26 10 false 6 5.26,3.615 5.594,3.844 0.333,0.229 10 false c47 5.677,3.604 6.323,3.813 0.646,0.208 10 false SYSB 5.292,3.406 5.604,3.646 0.313,0.24 10 false 12 3.49,2.615 4.448,2.906 0.958,0.292 10 false P/SEAT F/R 3.458,3.385 4.375,3.667 0.917,0.281 10 false MPX-B NO.1 1.563,2.854 2.5,3.177 0.938,0.323 10 false from Battery 1.563,3.594 2.646,3.865 1.083,0.271 10 false from Battery 5.125,5.073 7.01,5.635 1.885,0.563 10 false Power Seat Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.


Result
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU). A
DTC U1002 is output from main body ECU (multiplex network body ECU). B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER SEAT SWITCH ASSEMBLY CAN BRANCH WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER SEAT SWITCH ASSEMBLY CAN BRANCH WIRE)
a.
U165533E01
0.129,0.055 0.302,0.223 0.173,0.168 10 *a 1.882,1.577 2.317,1.746 0.435,0.168 10 MPX2 1.801,1.834 2.236,2.002 0.435,0.168 10 MPX1 1.855,1.665 1.738,1.665 1.738,1.665 1.605,1.582 false 1.76,1.937 1.63,1.937 1.63,1.937 1.519,1.582 false 0.495,1.286 0.748,1.425 0.253,0.139 10 c47

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power seat switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c47-8 (MPX1) - c47-7 (MPX2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Seat Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SEAT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SEAT SWITCH ASSEMBLY (MPX1, MPX2)

3.CHECK HARNESS AND CONNECTOR (POWER SEAT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165536E01
0.528,1.184 0.614,1.184 0.614,1.184 0.902,1.42 false 0.12,0.073 0.316,0.269 0.196,0.196 10 *a 0.178,1.104 0.592,1.248 0.415,0.144 10 +B2 2.898,1.495 3.312,1.639 0.415,0.144 10 +B2 0.291,0.659 0.540,0.803 0.250,0.144 10 c47 2.929,0.599 3.179,0.743 0.250,0.144 10 c46 0.146,1.691 0.560,1.834 0.415,0.144 10 SYSB 2.812,0.96 3.226,1.104 0.415,0.144 10 GND 2.868,1.577 2.782,1.577 2.782,1.577 2.597,1.418 false 0.648,1.768 0.734,1.768 0.734,1.768 0.919,1.609 false 2.571,1.216 2.688,1.054 2.688,1.054 2.799,1.054 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the power seat switch assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
c46-6 (+B2) - Body ground Always 11 to 14 V
c47-12 (SYSB) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c46-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Power Seat Switch Assembly)


OK

REPLACE POWER SEAT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR