Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  U1115  Lost Communication with Tilt and Telescopic Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1115 There is no communication from the multiplex tilt and telescopic ECU.
·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Power source or inside of multiplex tilt and telescopic ECU

·

Multiplex tilt and telescopic ECU ground circuit

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C251485E15
5.616,0.935 6.221,1.075 0.605,0.140 10 CANP 5.633,1.535 6.238,1.674 0.605,0.140 10 CANN 5.381,0.825 5.475,0.964 0.095,0.140 10 3 5.296,1.424 5.474,1.564 0.178,0.140 10 11 5.616,2.974 6.221,3.113 0.605,0.140 10 ECUB 5.381,2.863 5.475,3.003 0.095,0.140 10 9 5.616,2.403 6.221,2.542 0.605,0.140 10 +B 5.381,2.292 5.475,2.432 0.095,0.140 10 2 5.616,4.168 6.221,4.308 0.605,0.140 10 GND 5.381,4.058 5.475,4.197 0.095,0.140 10 1 5.616,4.751 6.221,4.891 0.605,0.140 10 GND2 5.633,3.573 6.238,3.713 0.605,0.140 10 IG 5.381,4.641 5.475,4.781 0.095,0.140 10 8 5.296,3.463 5.474,3.602 0.178,0.140 10 10 1.661,0.846 1.842,0.985 0.181,0.140 10 5 1.661,1.424 1.839,1.564 0.178,0.140 10 16 0.178,2.035 2.446,2.276 2.268,0.241 10 No. 8 CAN Junction Connector 1.607,2.391 2.388,2.529 0.781,0.138 10 from Battery 1.061,3.554 3.129,3.692 2.068,0.138 10 from IG1 NO.1 Relay 0.178,1.862 1.789,2.015 1.611,0.152 10 E136 3.561,3.414 4.459,3.573 0.898,0.159 10 ECU-IG NO.2 3.561,2.829 4.459,2.988 0.898,0.159 10 MPX-B NO.1 3.801,2.223 4.214,2.382 0.413,0.159 10 TI&TE 5.498,5.512 6.606,5.831 1.107,0.319 10 Multiplex Tilt and Telescopic ECU 5.498,5.33 6.002,5.486 0.503,0.156 10 E144 1.579,2.973 2.360,3.111 0.781,0.138 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.


Result
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU). A
DTC U1002 is output from main body ECU (multiplex network body ECU). B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)
a.
C251486E14
1.427,0.115 2.031,0.438 0.604,0.323 2.115,1.083 2.438,1.573 2.438,1.573 2.594,1.573 false 2.115,0.917 2.563,0.469 2.563,0.469 2.708,0.469 false 0.073,0.063 0.344,0.26 0.271,0.198 10 false *a 1.563,0.198 2.042,0.385 0.479,0.188 10 false E144 2.76,0.385 3.24,0.563 0.479,0.177 10 false CANP 2.635,1.49 3.188,1.688 0.552,0.198 10 false CANN

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the multiplex tilt and telescopic ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-3 (CANP) - E144-11 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)
a.
U165223E01
1.526,0.208 1.872,0.346 0.346,0.139 10 E144 2.521,1.085 2.663,1.28 2.663,1.28 2.812,1.28 false 2.521,0.913 2.688,0.771 2.688,0.771 2.837,0.771 false 0.069,0.062 0.343,0.263 0.274,0.201 10 *a 2.88,0.696 3.299,0.835 0.420,0.139 10 GND 2.855,1.203 3.274,1.341 0.420,0.139 10 GND2 2.363,1.1 2.537,1.518 2.537,1.518 2.686,1.518 false 2.361,0.894 2.685,0.468 2.685,0.468 2.834,0.468 false 2.877,0.393 3.297,0.531 0.420,0.139 10 +B 2.729,1.44 3.148,1.579 0.420,0.139 10 ECUB 2.211,1.1 2.374,1.796 2.374,1.796 2.522,1.796 false 2.565,1.718 2.985,1.857 0.420,0.139 10 IG

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E144-2 (+B) - Body ground Always 11 to 14 V
E144-9 (ECUB) - Body ground Always 11 to 14 V
E144-10 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-1 (GND) - Body ground Always Below 1 Ω
E144-8 (GND2) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR