Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either Condition is met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

ECM CAN main wire or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C334614E10
5.229,1.063 5.615,1.292 0.385,0.229 10 false A52 5.271,0.854 5.573,1.073 0.302,0.219 10 false 10 5.646,0.958 6.219,1.167 0.573,0.208 10 false CANH 5.24,1.646 5.615,1.823 0.375,0.177 10 false A52 5.292,1.448 5.604,1.656 0.313,0.208 10 false 11 5.646,1.75 6.177,1.938 0.531,0.188 10 false CANL 5.24,2.479 5.604,2.719 0.365,0.24 10 false A52 5.333,2.271 5.594,2.469 0.26,0.198 10 false 1 5.646,2.479 6.188,2.698 0.542,0.219 10 false BATT 5.24,3.417 5.604,3.625 0.365,0.208 10 false A52 5.333,3.208 5.594,3.417 0.26,0.208 10 false 3 5.656,3.417 6.156,3.615 0.5,0.198 10 false +B 5.229,3.875 5.583,4.104 0.354,0.229 10 false A52 5.313,3.656 5.563,3.844 0.25,0.188 10 false 2 5.281,4.094 5.625,4.292 0.344,0.198 10 false 34 5.646,3.865 6.115,4.094 0.469,0.229 10 false +B2 5.24,2.969 5.615,3.177 0.375,0.208 10 false A52 5.302,2.75 5.604,2.958 0.302,0.208 10 false 28 5.646,2.958 6.188,3.208 0.542,0.25 10 false IGSW 5.24,4.292 5.615,4.479 0.375,0.188 10 false A52 5.646,4.281 6.167,4.49 0.521,0.208 10 false MREL 5.24,4.75 5.635,5 0.396,0.25 10 false A52 5.292,4.542 5.594,4.719 0.302,0.177 10 false 31 5.646,4.74 6.135,4.917 0.49,0.177 10 false EC 5.24,5.24 5.604,5.469 0.365,0.229 10 false C46 5.281,5.031 5.531,5.24 0.25,0.208 10 false 81 5.646,5.229 6.135,5.448 0.49,0.219 10 false E1 5.24,5.729 5.625,5.958 0.385,0.229 10 false C46 5.292,5.521 5.563,5.719 0.271,0.198 10 false 82 5.646,5.719 6.177,5.938 0.531,0.219 10 false ME01 5.24,6.229 5.646,6.49 0.406,0.26 10 false C46 5.292,6.01 5.604,6.24 0.313,0.229 10 false 42 5.646,6.229 6.135,6.49 0.49,0.26 10 false E02 5.24,6.719 5.573,6.958 0.333,0.24 10 false C46 5.292,6.5 5.604,6.677 0.313,0.177 10 false 43 5.646,6.708 6.094,6.958 0.448,0.25 10 false E01 5.229,7.208 5.563,7.427 0.333,0.219 10 false C46 5.292,6.99 5.563,7.188 0.271,0.198 10 false 23 5.646,7.198 6.208,7.458 0.563,0.26 10 false E04 5.229,7.708 5.583,7.896 0.354,0.188 10 false C46 5.292,7.479 5.552,7.698 0.26,0.219 10 false 21 5.646,7.698 6.115,7.896 0.469,0.198 10 false E05 5.906,8.302 6.354,8.51 0.448,0.208 10 false ECM 1.646,1.51 2.052,1.771 0.406,0.26 10 false 17 0.5,2.052 1.031,2.25 0.531,0.198 10 false E133 0.5,2.208 2.646,2.531 2.146,0.323 10 false No. 1 CAN Junction Connector 0.229,0.104 1.5,0.375 1.271,0.271 12 false for 1UR-FE: 1.646,0.917 1.979,1.208 0.333,0.292 10 false 7 1.833,2.49 3.417,2.792 1.583,0.302 10 false from Battery 1.302,2.958 3.021,3.271 1.719,0.313 10 false from IG2 MAIN Relay 3.698,2.292 5.052,2.531 1.354,0.24 10 false EFI MAIN NO.1 3.698,2.771 5.042,3 1.344,0.229 10 false ENG-IG2 NO.1 0.948,3.417 2.906,3.875 1.958,0.458 10 false from EFI MAIN NO.1 Relay 1.115,4.281 2.917,4.656 1.802,0.375 10 false to EFI MAIN NO.1 Relay

C334615E08
5.229,1.063 5.594,1.333 0.365,0.271 10 false A52 5.292,0.854 5.563,1.083 0.271,0.229 10 false 41 5.646,0.958 6.24,1.26 0.594,0.302 10 false CANH 5.24,1.646 5.583,1.948 0.344,0.302 10 false A52 5.292,1.438 5.573,1.646 0.281,0.208 10 false 49 5.646,1.76 6.219,2.156 0.573,0.396 10 false CANL 5.24,2.479 5.583,2.719 0.344,0.24 10 false A52 5.281,2.26 5.563,2.479 0.281,0.219 10 false 20 5.646,2.479 6.26,2.688 0.615,0.208 10 false BATT 5.25,3.427 5.635,3.688 0.385,0.26 10 false A52 5.333,3.208 5.646,3.427 0.313,0.219 10 false 2 5.646,3.417 6.135,3.719 0.49,0.302 10 false +B 5.25,3.865 5.688,4.125 0.438,0.26 10 false A52 5.333,3.667 5.563,3.865 0.229,0.198 10 false 1 5.292,4.094 5.729,4.365 0.438,0.271 10 false 44 5.646,3.854 6.135,4.115 0.49,0.26 10 false +B2 5.24,2.969 5.667,3.271 0.427,0.302 10 false A52 5.292,2.74 5.594,2.969 0.302,0.229 10 false 28 5.646,2.969 6.208,3.219 0.563,0.25 10 false IGSW 5.24,4.292 5.594,4.51 0.354,0.219 10 false A52 5.646,4.281 6.281,4.531 0.635,0.25 10 false MREL 5.24,4.75 5.625,4.979 0.385,0.229 10 false A52 5.292,4.552 5.615,4.76 0.323,0.208 10 false 32 5.646,4.74 6.146,4.969 0.5,0.229 10 false EC 5.24,5.24 5.635,5.521 0.396,0.281 10 false C46 5.292,5.042 5.604,5.26 0.313,0.219 10 false 81 5.646,5.229 6.125,5.448 0.479,0.219 10 false E1 5.229,5.802 5.615,6.052 0.385,0.25 10 false C46 5.292,5.594 5.542,5.802 0.25,0.208 10 false 21 5.646,5.802 6.188,5.99 0.542,0.188 10 false E02 5.24,7.135 5.667,7.406 0.427,0.271 10 false C46 5.292,6.927 5.583,7.177 0.292,0.25 10 false 22 5.646,7.135 6.156,7.365 0.51,0.229 10 false E01 5.229,6.365 5.667,6.667 0.438,0.302 10 false C46 5.292,6.167 5.594,6.375 0.302,0.208 10 false 44 5.646,6.354 6.177,6.542 0.531,0.188 10 false E04* 5.229,7.698 5.615,7.938 0.385,0.24 10 false C46 5.292,7.5 5.646,7.729 0.354,0.229 10 false 23 5.646,7.698 6.188,7.969 0.542,0.271 10 false E05* 5.927,8.292 6.438,8.531 0.51,0.24 10 false ECM 1.646,1.51 1.948,1.792 0.302,0.281 10 false 17 0.469,2.042 1.01,2.271 0.542,0.229 10 false E133 0.469,2.188 2.698,2.5 2.229,0.313 10 false No. 1 CAN Junction Connector 0.229,0.135 1.406,0.458 1.177,0.323 12 false for 1VD-FTV: 1.646,0.917 1.938,1.219 0.292,0.302 10 false 7 1.865,2.469 3.375,2.792 1.51,0.323 10 false from Battery 1.323,2.938 2.958,3.26 1.635,0.323 10 false from IG2 MAIN Relay 3.698,2.292 5.063,2.563 1.365,0.271 10 false EFI MAIN NO.1 3.698,2.771 4.969,3.052 1.271,0.281 10 false ENG-IG2 NO.1 0.979,3.417 2.99,3.76 2.01,0.344 10 false from EFI MAIN NO.1 Relay 1.135,4.271 2.979,4.677 1.844,0.406 10 false to EFI MAIN NO.1 Relay 0.406,7.458 2.396,7.667 1.99,0.208 10 false *: w/ DPF

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.

for 1UR-FE:

i.
U166172E02
2.396,0.802 2.656,0.563 2.656,0.563 2.802,0.563 false 2.313,0.802 2.594,0.219 2.594,0.219 2.74,0.219 false 0.323,1 0.792,1.292 0.469,0.292 10 false A52 0.094,0.052 0.365,0.281 0.271,0.229 10 false *a 2.771,0.146 3.271,0.365 0.5,0.219 10 false CANH 2.833,0.49 3.375,0.74 0.542,0.25 10 false CANL

Disconnect the cable from the negative (-) battery terminal.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-10 (CANH) - A52-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



b.

for 1VD-FTV:

i.
U166173E02
2.396,1.198 2.656,0.958 2.656,0.958 2.802,0.958 false 2.396,1.292 2.625,1.448 2.625,1.448 2.76,1.448 false 0.333,1 0.76,1.24 0.427,0.24 10 false A52 0.094,0.063 0.438,0.281 0.344,0.219 10 false *a 2.833,0.875 3.365,1.073 0.531,0.198 10 false CANH 2.792,1.354 3.313,1.552 0.521,0.198 10 false CANL

Disconnect the cable from the negative (-) battery terminal.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-41 (CANH) - A52-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)




OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

for 1UR-FE:

i.

Connect the cable to the negative (-) battery terminal.

U165109E01
0.772,1.44 1.039,1.582 0.267,0.142 10 A52 6.546,1.44 6.827,1.582 0.281,0.142 10 C46 0.099,0.078 0.364,0.220 0.265,0.142 10 *a 1.498,0.822 1.564,0.822 1.564,0.822 1.884,1.199 false 1.593,0.268 1.797,0.410 0.205,0.142 10 +B 1.694,0.613 1.761,0.613 1.761,0.613 1.975,1.189 false 1.409,0.549 1.688,0.691 0.279,0.142 10 +B2 2.613,1.38 2.792,0.755 2.792,0.755 2.898,0.755 false 1.887,1.668 1.48,2.219 1.48,2.219 1.392,2.219 false 2.181,1.64 1.859,2.458 1.859,2.458 1.77,2.458 false 1.124,0.748 1.502,0.890 0.378,0.142 10 BATT 1.169,2.152 1.387,2.294 0.218,0.142 10 EC 2.911,0.687 3.305,0.829 0.394,0.142 10 IGSW 1.349,2.399 1.768,2.541 0.420,0.142 10 MREL 4.984,2.183 5.061,2.183 5.061,2.183 5.229,1.682 false 5.138,2.421 5.215,2.421 5.215,2.421 5.327,1.668 false 5.413,1.332 4.796,0.632 4.796,0.632 4.707,0.632 false 5.701,1.194 5.874,0.768 5.874,0.768 5.944,0.768 false 5.501,1.194 5.657,0.576 5.657,0.576 5.736,0.576 false 4.771,2.123 5.035,2.265 0.264,0.142 10 E1 5.971,0.7 6.236,0.842 0.264,0.142 10 E04 4.75,2.341 5.136,2.483 0.386,0.142 10 ME01 4.327,0.77 4.606,0.912 0.280,0.142 10 E02 5.766,0.488 6.046,0.630 0.280,0.142 10 E05 2.071,1.187 1.905,0.335 1.905,0.335 1.798,0.335 false 4.433,0.574 4.713,0.716 0.280,0.142 10 E01 4.603,0.828 4.671,0.828 4.671,0.828 5.318,1.346 false

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



ii.

Disconnect the ECM connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-1 (BATT) - Body ground Always 11 to 14 V
A52-3 (+B) - Body ground Battery positive (+) voltage applied to terminal A52-34 (MREL) 11 to 14 V
A52-2 (+B2) - Body ground Battery positive (+) voltage applied to terminal A52-34 (MREL) 11 to 14 V
A52-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-31 (EC) - Body ground Always Below 1 Ω
C46-42 (E02) - Body ground Always Below 1 Ω
C46-43 (E01) - Body ground Always Below 1 Ω
C83-82 (ME01) - Body ground Always Below 1 Ω
C46-81 (E1) - Body ground Always Below 1 Ω
C46-23 (E04) - Body ground Always Below 1 Ω
C46-21 (E05) - Body ground Always Below 1 Ω




b.

for 1VD-FTV:

i.

Connect the cable to the negative (-) battery terminal.

U165116E01
0.772,1.44 1.039,1.582 0.267,0.142 10 A52 6.546,1.44 6.827,1.582 0.281,0.142 10 C46 0.099,0.078 0.364,0.220 0.265,0.142 10 *a 1.218,0.962 1.284,0.962 1.284,0.962 1.884,1.339 false 0.892,0.329 1.096,0.471 0.205,0.142 10 +B 1.134,0.613 1.2,0.613 1.2,0.613 1.863,1.189 false 0.856,0.551 1.134,0.693 0.279,0.142 10 +B2 2.608,1.376 2.788,0.75 2.788,0.75 2.893,0.75 false 1.985,1.668 1.761,2.219 1.761,2.219 1.672,2.219 false 2.363,1.738 1.901,2.43 1.901,2.43 1.812,2.43 false 0.844,0.888 1.222,1.030 0.378,0.142 10 BATT 1.449,2.152 1.667,2.294 0.218,0.142 10 EC 2.906,0.682 3.301,0.824 0.394,0.142 10 IGSW 1.409,2.357 1.829,2.499 0.420,0.142 10 MREL 4.984,2.183 5.061,2.183 5.061,2.183 5.229,1.682 false 5.511,1.346 4.796,0.66 4.796,0.66 4.707,0.66 false 5.701,1.194 5.874,0.768 5.874,0.768 5.944,0.768 false 5.515,1.194 5.797,0.295 5.797,0.295 5.876,0.295 false 4.771,2.123 5.035,2.265 0.264,0.142 10 E1 4.241,0.593 4.832,0.735 0.590,0.142 10 E04*A 5.905,0.219 6.185,0.361 0.280,0.142 10 E02 5.972,0.712 6.578,0.854 0.606,0.142 10 E05*A 5.603,1.194 5.874,0.488 5.874,0.488 5.944,0.488 false 1.973,1.201 1.205,0.391 1.205,0.391 1.097,0.391 false 5.974,0.425 6.254,0.567 0.280,0.142 10 E01

Text in Illustration
*A w/ DPF - -
*a Front view of wire harness connector
(to ECM)
- -

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



ii.

Disconnect the ECM connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-20 (BATT) - Body ground Always 11 to 14 V
A52-2 (+B) - Body ground Battery positive (+) voltage applied to terminal A52-44 (MREL) 11 to 14 V
A52-1 (+B2) - Body ground Battery positive (+) voltage applied to terminal A52-44 (MREL) 11 to 14 V
A52-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-32 (EC) - Body ground Always Below 1 Ω
C46-21 (E02) - Body ground Always Below 1 Ω
C46-22 (E01) - Body ground Always Below 1 Ω
C46-81 (E1) - Body ground Always Below 1 Ω
C46-44 (E04) - Body ground* Always Below 1 Ω
C46-23 (E05) - Body ground* Always Below 1 Ω


*: w/ DPF


Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 1VD-FTV) B
NG C




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR