Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either Condition is met:
·

Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Airbag sensor assembly CAN branch wire or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

C250925E29
5.615,0.677 6.24,0.958 0.625,0.281 10 false CANH 5.615,1.271 6.073,1.479 0.458,0.208 10 false CANL 5.615,2.135 5.917,2.354 0.302,0.219 10 false IG2 1.604,2.135 3.031,2.75 1.427,0.615 10 false from IG2 MAIN Relay 3.802,1.948 4.604,2.177 0.802,0.229 10 false A/BAG-IG2 5.615,2.729 5.917,2.958 0.302,0.229 10 false E1 5.615,3.323 5.927,3.5 0.313,0.177 10 false E2 5.313,0.531 5.573,0.698 0.26,0.167 10 false 13 5.302,1.125 5.531,1.281 0.229,0.156 10 false 22 1.667,0.583 1.906,0.781 0.24,0.198 10 false 4 1.667,1.177 1.906,1.385 0.24,0.208 10 false 14 5.313,1.969 5.552,2.125 0.24,0.156 10 false 21 5.333,2.563 5.667,2.802 0.333,0.24 10 false 25 5.333,3.177 5.76,3.469 0.427,0.292 10 false 26 0.458,1.625 0.875,1.813 0.417,0.188 10 false E135 0.448,1.771 2.458,2.031 2.01,0.26 10 false No. 2 CAN Junction Connector 5.219,3.917 5.688,4.198 0.469,0.281 10 false E47 5.208,4.063 7.063,4.625 1.854,0.563 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U156235E01
0.042,0.052 0.277,0.241 0.235,0.189 10 *a 2.445,1.662 2.867,1.803 0.422,0.141 10 CANL 2.574,0.485 2.995,0.626 0.422,0.141 10 CANH 0.358,1.051 0.630,1.187 0.272,0.137 10 E47 2.014,1.018 2.459,0.558 2.459,0.558 2.545,0.558 false 2.136,1.379 2.346,1.737 2.346,1.737 2.432,1.737 false

Disconnect the cable from the negative (-) battery terminal and wait for at least 90 seconds.


b.

Disconnect the airbag sensor assembly connector (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-13 (CANH) - E47-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U156236E01
0.042,0.052 0.277,0.241 0.235,0.189 10 *a 0.373,1.059 0.648,1.195 0.276,0.137 10 E47 2.686,0.917 3.107,1.058 0.422,0.141 10 IG2 2.24,1.275 2.522,0.992 2.522,0.992 2.673,0.992 false 2.197,1.769 2.700,1.911 0.503,0.141 10 E1 1.014,1.769 1.517,1.911 0.503,0.141 10 E2 1.661,1.379 1.404,1.844 1.404,1.844 1.258,1.844 false 1.781,1.379 2.038,1.844 2.038,1.844 2.184,1.844 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E47-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-25 (E1) - Body ground Always Below 1 Ω
E47-26 (E2) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR