Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  U1115  Lost Communication with Tilt and Telescopic Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1115 There is no communication from the multiplex tilt and telescopic ECU.
·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Power source or inside of multiplex tilt and telescopic ECU

·

Multiplex tilt and telescopic ECU ground circuit

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C251485E20
1.646,0.813 1.885,1.021 0.24,0.208 10 false 5 1.646,1.417 2.021,1.646 0.375,0.229 10 false 16 0.427,1.885 0.896,2.156 0.469,0.271 10 false E136 0.427,2.021 2.708,2.354 2.281,0.333 10 false No. 8 CAN Junction Connector 1.51,2.354 2.438,2.583 0.927,0.229 10 false from Battery 3.802,2.24 4.427,2.469 0.625,0.229 10 false TI&TE 5.5,5.49 6.875,6.177 1.375,0.688 10 false Multiplex Tilt and Telescopic ECU 5.625,0.927 6.125,1.156 0.5,0.229 10 false CANP 5.625,1.51 6.167,1.771 0.542,0.26 10 false CANN 5.625,2.385 6.115,2.615 0.49,0.229 10 false +B 5.354,0.823 5.479,0.99 0.125,0.167 10 false 3 5.323,1.385 5.677,1.667 0.354,0.281 10 false 11 5.365,2.25 5.5,2.417 0.135,0.167 10 false 2 3.656,2.833 4.75,3.094 1.094,0.26 10 false MPX-B NO.1 1.5,2.979 2.385,3.198 0.885,0.219 10 false from Battery 5.625,2.969 6.219,3.219 0.594,0.25 10 false ECUB 5.354,2.844 5.479,3.042 0.125,0.198 10 false 9 3.646,3.385 4.833,3.625 1.188,0.24 10 false ECU-IG NO.2 1,3.542 2.583,3.792 1.583,0.25 10 false from IG1 NO.1 Relay 5.625,3.563 6.125,3.781 0.5,0.219 10 false IG 5.313,3.427 5.719,3.708 0.406,0.281 10 false 10 5.625,4.74 6.104,4.958 0.479,0.219 10 false GND2 5.385,4.625 5.51,4.802 0.125,0.177 10 false 8 5.625,4.146 6.125,4.396 0.5,0.25 10 false GND 5.396,4.042 5.479,4.177 0.083,0.135 10 false 1 5.5,5.323 6.042,5.531 0.542,0.208 10 false E144

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.


Result
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU). A
DTC U1002 is output from main body ECU (multiplex network body ECU). B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU CAN BRANCH WIRE)
a.
C251486E15
0.198,0.844 0.729,1.167 0.531,0.323 2.115,1.083 2.438,1.573 2.438,1.573 2.594,1.573 false 2.115,0.917 2.563,0.469 2.563,0.469 2.708,0.469 false 0.073,0.063 0.344,0.26 0.271,0.198 10 false *a 0.302,0.927 0.729,1.167 0.427,0.24 10 false E144 2.76,0.385 3.323,0.583 0.563,0.198 10 false CANP 2.635,1.49 3.219,1.708 0.583,0.219 10 false CANN

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the multiplex tilt and telescopic ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-3 (CANP) - E144-11 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY AND BODY GROUND)
a.
U165223E01
1.526,0.208 1.872,0.346 0.346,0.139 10 E144 2.521,1.085 2.663,1.28 2.663,1.28 2.812,1.28 false 2.521,0.913 2.688,0.771 2.688,0.771 2.837,0.771 false 0.069,0.062 0.343,0.263 0.274,0.201 10 *a 2.88,0.696 3.299,0.835 0.420,0.139 10 GND 2.855,1.203 3.274,1.341 0.420,0.139 10 GND2 2.363,1.1 2.537,1.518 2.537,1.518 2.686,1.518 false 2.361,0.894 2.685,0.468 2.685,0.468 2.834,0.468 false 2.877,0.393 3.297,0.531 0.420,0.139 10 +B 2.729,1.44 3.148,1.579 0.420,0.139 10 ECUB 2.211,1.1 2.374,1.796 2.374,1.796 2.522,1.796 false 2.565,1.718 2.985,1.857 0.420,0.139 10 IG

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E144-2 (+B) - Body ground Always 11 to 14 V
E144-9 (ECUB) - Body ground Always 11 to 14 V
E144-10 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-1 (GND) - Body ground Always Below 1 Ω
E144-8 (GND2) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR