Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Bus Buffer ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Bus Buffer ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Accessory Gateway" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Bus Buffer ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


Bus buffer ECU CAN branch wire or connector

WIRING DIAGRAM

C288320E15
5.604,1.875 6.625,2.188 1.021,0.313 10 false E173 5.604,2.042 6.625,2.354 1.021,0.313 10 false Bus Buffer ECU 5.635,0.896 6.208,1.208 0.573,0.313 10 false CAN+ 1.656,1.385 2.208,1.635 0.552,0.25 10 false 20 1.667,0.802 2.24,1.063 0.573,0.26 10 false 9 5.427,1.396 5.646,1.635 0.219,0.24 10 false 1 5.427,0.813 5.604,1.094 0.177,0.281 10 false 2 0.208,1.875 2.302,2.104 2.094,0.229 10 false E152 0.208,2.042 2.375,2.385 2.167,0.344 10 false No. 5 CAN Junction Connector 5.635,1.479 6.219,1.729 0.583,0.25 10 false CAN-

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
a.
U165543E01
0.1,0.132 0.363,0.285 0.262,0.154 10 *a 2.764,0.831 3.193,0.984 0.429,0.154 10 CAN- 2.558,0.404 2.987,0.557 0.429,0.154 10 CAN+ 2.103,1.172 2.524,0.905 2.524,0.905 2.741,0.905 false 2.524,0.49 2.34,0.49 2.34,0.49 1.896,1.149 false 1.488,0.295 1.836,0.435 0.348,0.140 10 E173

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the bus buffer ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E173-2 (CAN+) - E173-1 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Bus Buffer ECU)



OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)