Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  U1002  Lost Communication with Gateway Module (Sensor Bus)  


DESCRIPTION

·

The driving support ECU assembly will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to local bus.

·

When the driving support ECU assembly receives a response signal from the ECUs connected to local bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to local bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to local bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to local bus, the driving support ECU assembly determines that a malfunction exists.

DTC Code DTC Detection Condition Trouble Area
U1002 Driving support ECU assembly cannot receive signals from all ECUs that have been memorized as those connected to local bus.
·

Open or short in local bus CAN main wire or connector

·

Open or short in local bus CAN branch wire or connector

·

Driving support ECU assembly

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

No. 10 CAN junction connector




WIRING DIAGRAM

C347088E18
1.229,0.979 1.844,1.177 0.615,0.198 10 false CA1P 1.229,1.385 1.844,1.583 0.615,0.198 10 false CA1N 1.719,1.281 2.333,1.479 0.615,0.198 10 false 9 1.729,0.875 2.344,1.073 0.615,0.198 10 false 8 1.26,2.875 1.875,3.073 0.615,0.198 10 false CA1P 1.229,3.521 1.844,3.719 0.615,0.198 10 false CA1N 1.729,3.292 2.344,3.49 0.615,0.198 10 false 6 1.74,2.875 2.354,3.073 0.615,0.198 10 false 5 3.156,2.865 3.771,3.063 0.615,0.198 10 false 5 3.083,3.281 3.698,3.479 0.615,0.198 10 false 15 3.063,1.281 3.677,1.479 0.615,0.198 10 false 17 3.146,0.865 3.76,1.063 0.615,0.198 10 false 7 0.563,1.792 2.51,2.146 1.948,0.354 10 false E164 0.563,1.958 1.969,2.719 1.406,0.76 10 false Driving Support ECU Assembly 5.25,1.781 6.792,2.167 1.542,0.385 10 false R20 5.26,1.958 7.135,2.438 1.875,0.479 10 false Forward Recognition Camera 5.688,0.875 6.302,1.073 0.615,0.198 10 false CANH 5.698,1.51 6.313,1.708 0.615,0.198 10 false CANL 4.042,0.875 4.656,1.073 0.615,0.198 10 false 6 5.458,0.854 6.073,1.052 0.615,0.198 10 false 6 5.406,1.292 6.021,1.49 0.615,0.198 10 false 12 4.042,1.281 4.656,1.479 0.615,0.198 10 false 16 0.5,3.792 2.042,4.177 1.542,0.385 10 false A72 0.5,3.969 1.99,4.656 1.49,0.688 10 false Millimeter Wave Radar Sensor Assembly 2.896,3.792 4.438,4.177 1.542,0.385 10 false E174 2.896,3.948 5.146,4.438 2.25,0.49 10 false No. 10 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK LOCAL BUS
a.
U165660E01
0.117,1.564 0.359,1.713 0.242,0.149 10 *b 0.117,0.052 0.359,0.201 0.242,0.149 10 *a 1.497,0.175 1.840,0.324 0.343,0.149 10 E164 0.305,0.339 0.704,0.488 0.399,0.149 10 CA1N 0.454,0.11 0.853,0.259 0.399,0.149 10 CA1P 1.276,0.798 0.95,0.434 0.95,0.434 0.781,0.434 false 0.941,0.193 1.144,0.193 1.144,0.193 1.364,0.798 false 0.324,2.438 0.592,2.587 0.268,0.149 10 E22 0.907,1.808 1.306,1.957 0.399,0.149 10 CG 2.294,2.763 2.535,2.992 2.535,2.992 2.704,2.992 false 1.674,2.267 1.348,1.904 1.348,1.904 1.179,1.904 false 2.734,2.903 3.133,3.052 0.399,0.149 10 BAT

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Resistance: Malfunction
E164-8 (CA1P) - E164-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short in line
E164-8 (CA1P) - E164-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
E164-8 (CA1P) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
E164-9 (CA1N) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
E164-8 (CA1P) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short
E164-9 (CA1N) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Driving Support ECU Assembly)
*B Front view of DLC3

Result
Result Proceed to
OK A
NG (Open circuit in CAN main bus wire) B
NG (Short circuit between bus wire) C
NG
·

Ground short

·

+B short


D



A

2.CHECK FOR DTC OUTPUT

B

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (FORWARD RECOGNITION CAMERA)

C

8.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA)

D

15.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA)
2.CHECK FOR DTC OUTPUT

b.

Recheck for DTCs and check that no DTCs are output (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

OK:

DTC U1002 is not output.




OK

NG

REPLACE DRIVING SUPPORT ECU ASSEMBLY

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (FORWARD RECOGNITION CAMERA)
a.
U165416E01
2.082,1.547 2.243,1.772 2.243,1.772 2.376,1.772 false 2.46,0.97 2.283,0.97 2.283,0.97 2.062,1.23 false 0.086,0.064 0.263,0.218 0.177,0.154 10 *a 1.567,0.344 1.843,0.484 0.276,0.140 10 R20 2.478,0.884 2.946,1.021 0.468,0.137 10 CANH 2.401,1.683 2.869,1.820 0.468,0.137 10 CANL

Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-6 (CANH) - R20-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the R20 forward recognition camera connector.



NEXT

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
U165612E01
0.061,0.054 0.353,0.341 0.292,0.288 10 *a 0.742,1.784 1.211,1.935 0.468,0.151 10 CA1N 0.244,1.486 0.712,1.637 0.468,0.151 10 CA1P 1.593,0.161 1.860,0.301 0.267,0.140 10 A72 1.462,1.191 0.937,1.546 0.937,1.546 0.751,1.546 false 1.255,1.858 1.427,1.858 1.427,1.858 1.632,1.22 false

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-5 (CA1P) - A72-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the A72 millimeter wave radar sensor assembly connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 10 CAN junction connector.

U165483E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 3.433,0.199 3.776,0.341 0.343,0.142 10 E174 2.306,0.248 2.876,0.392 0.569,0.144 10 CANH*b 2.407,1.331 2.976,1.475 0.569,0.144 10 CANL*b 3.783,1.022 4.254,1.438 4.254,1.438 4.352,1.438 false 3.366,1.026 3.06,1.401 3.06,1.401 2.962,1.401 false 3.783,0.844 4.314,0.338 4.314,0.338 4.412,0.338 false 3.366,0.839 2.995,0.324 2.995,0.324 2.897,0.324 false 4.443,0.274 5.013,0.417 0.569,0.144 10 CANH*c 4.376,1.373 4.946,1.517 0.569,0.144 10 CANL*c

Text in Illustration
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b to Millimeter Wave Radar Sensor Assembly
*c to Forward Recognition Camera - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E174-5 (CANH) - E174-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Millimeter wave radar sensor assembly
E174-6 (CANH) - E174-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Forward recognition camera


Result
Result Proceed to
OK A
NG (Millimeter wave radar sensor assembly CAN main wire) B
NG (Forward recognition camera CAN main wire) C



A

REPLACE NO. 10 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

8.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA)
a.
U165416E01
2.082,1.547 2.243,1.772 2.243,1.772 2.376,1.772 false 2.46,0.97 2.283,0.97 2.283,0.97 2.062,1.23 false 0.086,0.064 0.263,0.218 0.177,0.154 10 *a 1.567,0.344 1.843,0.484 0.276,0.140 10 R20 2.478,0.884 2.946,1.021 0.468,0.137 10 CANH 2.401,1.683 2.869,1.820 0.468,0.137 10 CANL

Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-6 (CANH) - R20-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

9.CONNECT CONNECTOR
9.CONNECT CONNECTOR
a.

Reconnect the R20 forward recognition camera connector.



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
10.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
U165612E01
0.061,0.054 0.353,0.341 0.292,0.288 10 *a 0.742,1.784 1.211,1.935 0.468,0.151 10 CA1N 0.244,1.486 0.712,1.637 0.468,0.151 10 CA1P 1.593,0.161 1.860,0.301 0.267,0.140 10 A72 1.462,1.191 0.937,1.546 0.937,1.546 0.751,1.546 false 1.255,1.858 1.427,1.858 1.427,1.858 1.632,1.22 false

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-5 (CA1P) - A72-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

11.CONNECT CONNECTOR
11.CONNECT CONNECTOR
a.

Reconnect the A72 millimeter wave radar sensor assembly connector.



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 10 CAN junction connector.

U165458E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 3.433,0.199 3.776,0.341 0.343,0.142 10 E174 2.306,0.248 2.876,0.392 0.569,0.144 10 CANH*b 2.407,1.331 2.976,1.475 0.569,0.144 10 CANL*b 3.993,1.022 4.464,1.438 4.464,1.438 4.562,1.438 false 3.366,1.026 3.06,1.401 3.06,1.401 2.962,1.401 false 3.993,0.844 4.524,0.338 4.524,0.338 4.622,0.338 false 3.366,0.839 2.995,0.324 2.995,0.324 2.897,0.324 false 4.653,0.274 5.223,0.417 0.569,0.144 10 CANH*d 4.31,0.05 4.879,0.193 0.569,0.144 10 CANH*c 4.586,1.373 5.156,1.517 0.569,0.144 10 CANL*d 4.275,1.548 4.844,1.692 0.569,0.144 10 CANL*c 3.803,0.843 4.14,0.126 4.14,0.126 4.294,0.126 false 3.811,1.008 4.095,1.614 4.095,1.614 4.252,1.614 false

Text in Illustration
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b to Millimeter Wave Radar Sensor Assembly
*c to Forward Recognition Camera *d to Driving Support ECU Assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E174-5 (CANH) - E174-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Millimeter wave radar sensor assembly
E174-6 (CANH) - E174-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Driving support ECU assembly
E174-7 (CANH) - E174-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera


Result
Result Proceed to
OK A
NG (Millimeter wave radar sensor assembly CAN main wire) B
NG (Forward recognition camera CAN main wire) C
NG (Driving support ECU assembly CAN branch wire) D



A

REPLACE NO. 10 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

D

13.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the E174 No. 10 CAN junction connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
a.
U165654E01
2.26,1.082 2.724,0.64 2.724,0.64 2.9,0.64 false 2.733,0.395 2.535,0.395 2.535,0.395 2.144,1.082 false 0.095,0.069 0.296,0.232 0.201,0.163 10 *a 1.544,0.38 1.891,0.517 0.347,0.137 10 E164 2.751,0.312 3.254,0.448 0.503,0.137 10 CA1P 2.918,0.564 3.307,0.701 0.389,0.137 10 CA1N

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E164-8 (CA1P) - E164-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA)
a.
U165410E01
2.468,0.829 2.879,0.966 0.411,0.137 10 CANH 0.058,0.06 0.500,0.197 0.442,0.137 10 *a 0.608,1.08 0.885,1.216 0.277,0.137 10 R20 0.058,1.939 0.500,2.076 0.442,0.137 10 *b 0.429,2.621 0.699,2.758 0.270,0.137 10 E22 2.208,2.919 2.371,3.211 2.371,3.211 2.526,3.211 false 2.548,3.132 2.937,3.269 0.389,0.137 10 BAT 0.964,2.026 1.353,2.163 0.389,0.137 10 CG 1.647,2.475 1.437,2.101 1.437,2.101 1.282,2.101 false 2.084,1.131 2.291,0.912 2.291,0.912 2.446,0.912 false 2.084,1.43 2.303,1.632 2.303,1.632 2.457,1.632 false 2.48,1.554 2.868,1.691 0.389,0.137 10 CANL

Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-6 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R20-12 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R20-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R20-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

16.CONNECT CONNECTOR
16.CONNECT CONNECTOR
a.

Reconnect the R20 forward recognition camera connector.



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
17.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
U165661E01
0.117,1.617 0.359,1.766 0.242,0.149 10 *b 0.117,0.052 0.359,0.201 0.242,0.149 10 *a 0.376,0.568 0.647,0.707 0.270,0.139 10 A72 0.802,1.466 1.201,1.615 0.399,0.149 10 CA1N 0.417,1.216 0.816,1.365 0.399,0.149 10 CA1P 1.48,1.029 1.061,1.3 1.061,1.3 0.892,1.3 false 1.294,1.553 1.497,1.553 1.497,1.553 1.637,1.029 false 0.324,2.438 0.592,2.587 0.268,0.149 10 E22 0.907,1.808 1.306,1.957 0.399,0.149 10 CG 2.294,2.763 2.535,2.992 2.535,2.992 2.704,2.992 false 1.674,2.267 1.348,1.904 1.348,1.904 1.179,1.904 false 2.734,2.903 3.133,3.052 0.399,0.149 10 BAT

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-5 (CA1P) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A72-6 (CA1N) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A72-5 (CA1P) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-6 (CA1N) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

18.CONNECT CONNECTOR
18.CONNECT CONNECTOR
a.

Reconnect the A72 millimeter wave radar sensor assembly connector.



NEXT

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 CAN JUNCTION CONNECTOR)
19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 10 CAN junction connector.

U165488E01
0.09,0.045 0.315,0.215 0.225,0.170 10 *a 4.466,0.045 4.691,0.215 0.225,0.170 10 *b 0.755,0.197 1.324,0.340 0.569,0.144 10 CANH*c 0.758,1.332 1.328,1.476 0.569,0.144 10 CANL*c 2.816,1.502 3.385,1.646 0.569,0.144 10 CANL*d 3.229,1.271 3.799,1.415 0.569,0.144 10 CANL*e 3.264,0.307 3.834,0.451 0.569,0.144 10 CANH*e 2.837,0.062 3.406,0.205 0.569,0.144 10 CANH*d 0.466,0.787 0.809,0.929 0.343,0.142 10 E174 2.362,0.844 2.706,0.131 2.706,0.131 2.804,0.131 false 1.34,0.271 1.581,0.271 1.581,0.271 2.013,0.836 false 2.564,0.826 3.019,0.378 3.019,0.378 3.233,0.378 false 2.362,1.003 2.685,1.565 2.685,1.565 2.783,1.565 false 1.292,1.399 1.534,1.399 1.534,1.399 2.013,1.01 false 2.564,1.02 2.998,1.353 2.998,1.353 3.212,1.353 false 5.54,0.142 5.809,0.284 0.269,0.142 10 E22 6.624,1.287 7.013,1.430 0.389,0.144 10 BAT 6.227,1.104 6.377,1.352 6.377,1.352 6.591,1.352 false 5.601,0.644 5.159,0.297 5.159,0.297 5.061,0.297 false 4.823,0.229 5.212,0.372 0.389,0.144 10 CG

Text in Illustration
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b Front view of DLC3
*c to Millimeter Wave Radar Sensor Assembly *d to Forward Recognition Camera
*e to Driving Support ECU Assembly - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E174-5 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Millimeter wave radar sensor assembly
E174-15 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E174-5 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E174-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E174-6 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Forward recognition camera
E174-16 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E174-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E174-16 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E174-7 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Driving support ECU assembly
E174-17 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E174-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E174-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result
Result Proceed to
OK A
NG (Millimeter wave radar sensor assembly CAN main wire) B
NG (Forward recognition camera CAN main wire) C
NG (Driving support ECU assembly CAN branch wire) D



A

REPLACE NO. 10 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

D

20.CONNECT CONNECTOR
20.CONNECT CONNECTOR
a.

Reconnect the E174 No. 10 CAN junction connector.



NEXT

21.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
21.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
a.
U165663E01
2.257,1.071 2.664,0.63 2.664,0.63 2.84,0.63 false 2.673,0.385 2.475,0.385 2.475,0.385 2.141,1.071 false 0.092,0.058 0.293,0.221 0.201,0.163 10 *a 1.575,0.37 1.922,0.507 0.347,0.137 10 E164 2.691,0.301 3.194,0.438 0.503,0.137 10 CA1P 2.857,0.554 3.246,0.691 0.389,0.137 10 CA1N 0.142,1.824 0.383,1.973 0.242,0.149 10 *b 0.348,2.698 0.616,2.847 0.268,0.149 10 E22 0.931,2.068 1.330,2.217 0.399,0.149 10 CG 2.217,2.967 2.457,3.196 2.457,3.196 2.626,3.196 false 1.699,2.527 1.372,2.163 1.372,2.163 1.203,2.163 false 2.657,3.107 3.056,3.256 0.399,0.149 10 BAT

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E164-8 (CA1P) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E164-9 (CA1N) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E164-8 (CA1P) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E164-9 (CA1N) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)