Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Inner Rear View Mirror Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Inner Rear View Mirror Assembly Communication Stop Mode Either Condition is met:
·

Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Inner Rear View Mirror Assembly Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Inner rear view mirror assembly CAN branch wire or connector

·

Power source circuit of inner rear view mirror assembly

·

Inner rear view mirror assembly ground circuit

·

Inner rear view mirror assembly



WIRING DIAGRAM

C241189E31
1.667,0.51 1.99,0.76 0.323,0.25 10 false 9 1.667,1.073 2.042,1.344 0.375,0.271 10 false 19 0.49,1.531 0.927,1.719 0.438,0.188 10 false E151 0.49,1.688 2.469,2.01 1.979,0.323 10 false No. 3 CAN Junction Connector 5.302,1.063 5.5,1.292 0.198,0.229 10 false 10 5.385,0.469 5.51,0.656 0.125,0.188 10 false 9 5.385,2.5 5.5,2.677 0.115,0.177 10 false 2 5.385,1.927 5.51,2.125 0.125,0.198 10 false 1 5.625,1.167 6.042,1.354 0.417,0.188 10 false CANL 5.604,0.594 6.094,0.76 0.49,0.167 10 false CANH 5.625,2.656 5.99,2.854 0.365,0.198 10 false E 5.604,2.031 5.979,2.229 0.375,0.198 10 false IG 3.063,1.854 4.115,2.125 1.052,0.271 10 false ECU-IG NO.2 1.01,2.073 2.406,2.396 1.396,0.323 10 false from IG1 NO.1 Relay 4.938,3.271 5.719,3.448 0.781,0.177 10 false R16 4.938,3.438 7.125,3.708 2.188,0.271 10 false Inner Rear View Mirror Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (INNER REAR VIEW MIRROR ASSEMBLY CAN BRANCH WIRE)
a.
U165579E01
2.024,1.275 2.316,1.455 2.316,1.455 2.445,1.455 false 2.324,1.807 2.115,1.807 2.115,1.807 1.855,1.275 false 2.487,1.359 3.118,1.573 0.632,0.214 10 CANL 2.375,1.711 2.910,1.918 0.535,0.206 10 CANH 0.102,0 0.417,0.239 0.316,0.239 10 *a 0.536,0.884 0.867,1.073 0.331,0.190 10 R16

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the inner rear view mirror assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-9 (CANH) - R16-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO INNER REAR VIEW MIRROR ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165580E02
1.333,1.063 1.042,0.875 1.042,0.875 0.906,0.875 false 1.052,0.51 1.26,0.51 1.26,0.51 1.521,1.042 false 0.688,0.802 1.042,1.042 0.354,0.24 10 false IG 0.885,0.438 1.24,0.625 0.354,0.188 10 false E 0.115,0.094 0.5,0.385 0.385,0.292 10 false *a 2.604,0.875 3.146,1.229 0.542,0.354 10 false R16

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R16-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-2 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


OK

REPLACE INNER REAR VIEW MIRROR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR