Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Either Condition is met:
·

Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Forward recognition camera CAN branch wire or connector

·

Power source circuit of forward recognition camera

·

Forward recognition camera ground circuit

·

Forward recognition camera



WIRING DIAGRAM

C306897E34
5.083,4.156 7.094,4.625 2.01,0.469 10 false Forward Recognition Camera 5.083,3.99 5.615,4.271 0.531,0.281 10 false R20 0.135,1.75 0.542,1.958 0.406,0.208 10 false E151 0.156,1.948 2.365,2.125 2.208,0.177 10 false No. 3 CAN Junction Connector 1.74,2.313 3.229,2.667 1.49,0.354 10 false from IG1 NO.1 Relay 3.958,2.135 5.063,2.438 1.104,0.302 10 false ECU-IG NO.2 5.656,1.021 6.177,1.177 0.521,0.156 10 false CA1P 5.656,1.531 6.177,1.688 0.521,0.156 10 false CA1N 5.656,2.354 6.177,2.51 0.521,0.156 10 false IGB 5.656,3.146 6.177,3.302 0.521,0.156 10 false GND 5.396,0.896 5.594,1.083 0.198,0.188 10 false 5 5.344,1.427 5.583,1.573 0.24,0.146 10 false 11 5.417,2.208 5.573,2.385 0.156,0.177 10 false 7 5.365,3.021 5.615,3.208 0.25,0.188 10 false 10 1.542,0.875 1.698,1.052 0.156,0.177 10 false 9 1.542,1.406 1.802,1.583 0.26,0.177 10 false 19

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA CAN BRANCH WIRE)
a.
U165417E01
1.944,1.547 2.243,1.772 2.243,1.772 2.376,1.772 false 2.46,0.97 2.283,0.97 2.283,0.97 1.924,1.23 false 0.086,0.064 0.263,0.218 0.177,0.154 10 *a 1.567,0.344 1.843,0.484 0.276,0.140 10 R20 2.478,0.884 2.946,1.021 0.468,0.137 10 CA1P 2.401,1.683 2.869,1.820 0.468,0.137 10 CA1N

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-5 (CA1P) - R20-11 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FORWARD RECOGNITION CAMERA (CA1P, CA1N)

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)
a.
U165422E01
1.788,1.548 2.061,1.865 2.061,1.865 2.194,1.865 false 0.829,1.772 1.006,1.772 1.006,1.772 1.364,1.511 false 0.086,0.064 0.263,0.218 0.177,0.154 10 *a 1.567,0.344 1.843,0.484 0.276,0.140 10 R20 0.475,1.683 0.943,1.820 0.468,0.137 10 IGB 2.219,1.776 2.687,1.913 0.468,0.137 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R20-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-10 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)


OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR