Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Millimeter Wave Radar Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Millimeter Wave Radar Sensor Communication Stop Mode Either Condition is met:
·

Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Millimeter Wave Radar Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Millimeter wave radar sensor assembly CAN branch wire or connector

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C241189E32
1.667,0.51 1.917,0.656 0.25,0.146 10 false 6 1.667,1.073 1.917,1.219 0.25,0.146 10 false 16 0.49,1.531 0.906,1.677 0.417,0.146 10 false E151 0.49,1.688 2.771,2.021 2.281,0.333 10 false No. 3 CAN Junction Connector 5.375,1.063 5.5,1.24 0.125,0.177 10 false 2 5.385,0.469 5.51,0.656 0.125,0.188 10 false 3 5.385,2.5 5.5,2.677 0.115,0.177 10 false 1 5.385,1.927 5.51,2.125 0.125,0.198 10 false 8 5.625,1.167 6.042,1.354 0.417,0.188 10 false CA2L 5.604,0.594 6.094,0.76 0.49,0.167 10 false CA2H 5.625,2.656 6.313,2.865 0.688,0.208 10 false SGND 5.604,2.031 5.979,2.229 0.375,0.198 10 false IGB 3.063,1.854 4.042,2.083 0.979,0.229 10 false ECU-IG NO.2 1.01,2.073 2.406,2.385 1.396,0.313 10 false from IG1 NO.1 Relay 4.354,3.25 5.938,3.563 1.583,0.313 10 false A72 4.354,3.438 7.115,3.771 2.76,0.333 10 false Millimeter Wave Radar Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U165613E02
1.635,1.01 0.938,0.677 0.938,0.677 0.75,0.677 false 1.25,0.344 1.427,0.344 1.427,0.344 1.802,0.99 false 0.063,0.063 0.354,0.354 0.292,0.292 10 false *a 0.333,0.594 0.813,0.781 0.479,0.188 10 false CA2L 0.813,0.271 1.302,0.49 0.49,0.219 10 false CA2H 0.385,1.083 0.792,1.365 0.406,0.281 10 false A72

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-3 (CA2H) - A72-2 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MILLIMETER WAVE RADAR SENSOR ASSEMBLY (CA2H, CA2L)

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165614E01
0.061,0.054 0.353,0.341 0.292,0.288 10 *a 0.308,0.589 0.777,0.741 0.468,0.151 10 SGND 2.667,1.606 2.938,1.758 0.270,0.151 10 IGB 1.593,0.161 1.860,0.301 0.267,0.140 10 A72 1.462,1.003 1.01,0.678 1.01,0.678 0.824,0.678 false 2.639,1.691 2.405,1.691 2.405,1.691 2.021,1.22 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-1 (SGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR