Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255541 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69320 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184438E06
1.85,2.321 2.225,2.484 0.375,0.163 10 Lock 2.529,2.02 3.039,2.194 0.510,0.174 10 Unlock 3.877,0.407 6.366,0.771 2.489,0.364 10 Component without harness connected: (Front Door Lock LH) 4.458,1.948 4.662,2.132 0.205,0.184 10 L 6.218,1.948 6.517,2.128 0.298,0.180 10 UL 5.72,1.802 6.166,2.011 false 5.031,1.802 4.584,2.011 false 5.639,2.388 5.893,2.545 0.254,0.158 10 E 5.007,2.388 5.486,2.565 0.479,0.177 10 LSSR 5.267,2.027 5.204,2.368 false 5.484,2.004 5.665,2.362 false

a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the door lock assembly.




c.

for LHD:

B184437E03
2.429,0.678 2.849,0.848 0.420,0.170 10 Lock 2.023,2.02 2.530,2.200 0.507,0.180 10 Unlock 2.68,1.684 2.990,1.839 0.310,0.155 10 Off 4.155,0.233 6.635,0.610 2.480,0.377 10 Component without harness connected: (Front Door Lock LH) 5.315,2.347 5.446,2.528 0.131,0.180 10 E 4.482,2.251 4.723,2.404 0.240,0.153 10 UL 5.043,2.347 5.208,2.490 0.164,0.142 10 L 5.365,2.044 5.365,2.34 false 5.077,2.044 5.077,2.34 false 4.923,2.022 4.651,2.294 false

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
OFF 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω



If the result is not as specified, replace the door lock assembly.




Hide 69320 2.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144111E17
5.031,1.885 4.625,2.083 false 5.51,2.063 5.646,2.385 false 5.313,2.094 5.281,2.375 false 5.271,1.802 4.646,1.469 false 5.813,1.854 6.156,1.854 false 5.583,1.792 6.021,1.354 false 1.917,2.313 2.292,2.479 0.375,0.167 10 false Lock 2.594,2.01 3.104,2.188 0.51,0.177 10 false Unlock 3.938,0.396 6.427,0.76 2.49,0.365 10 false Component without harness connected: (Front Door Lock LH) 4.5,2.042 4.708,2.229 0.208,0.188 10 false U 4.417,1.396 4.719,1.573 0.302,0.177 10 false UL 5.625,2.406 5.792,2.656 0.167,0.25 10 false E 5.083,2.396 5.479,2.594 0.396,0.198 10 false LSSR 6.177,1.781 6.625,1.969 0.448,0.188 10 false UNDL 6.094,1.26 6.406,1.458 0.313,0.198 10 false DL

a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Set
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unset


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the door lock assembly.




c.

for LHD:

B144108E02
4.161,0.282 6.769,0.854 2.607,0.573 10 Component without harness connected: (Front Door Lock LH) 4.642,2.383 4.875,2.551 0.232,0.168 10 UL 5.133,2.383 5.365,2.551 0.232,0.168 10 L 5.588,2.383 5.820,2.551 0.232,0.168 10 E 4.988,2.088 4.744,2.366 false 5.161,2.362 5.177,2.082 false 5.455,2.04 5.616,2.362 false 3.199,1.307 3.682,1.484 0.482,0.177 10 Unlock 3.385,0.57 3.867,0.747 0.482,0.177 10 Lock

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
OFF 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω



If the result is not as specified, replace the door lock assembly.




Hide 69310 3.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184439E27
5.177,1.979 5.021,2.333 false 5.385,1.99 5.615,2.354 false 4.896,1.76 4.344,1.875 false 5.677,1.771 6.083,1.896 false 1.01,1.906 1.594,2.094 0.583,0.188 10 false Unlock 1.865,2.208 2.219,2.458 0.354,0.25 10 false Lock 4.021,0.219 6.531,0.688 2.51,0.469 10 false Component without harness connected: (Front Door Lock RH) 5.438,2.354 5.885,2.594 0.448,0.24 10 false LSSR 4.948,2.354 5.094,2.552 0.146,0.198 10 false E 4.26,1.823 4.708,2.156 0.448,0.333 10 false L 6.115,1.823 6.625,2.167 0.51,0.344 10 false UL

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the door lock assembly.




c.

for RHD:

B144104E02
4.045,0.166 6.721,0.781 2.676,0.615 10 Component without harness connected: (Front Door Lock RH) 4.781,2.369 5.013,2.537 0.232,0.168 10 UL 5.157,2.369 5.389,2.537 0.232,0.168 10 L 5.51,2.369 5.742,2.537 0.232,0.168 10 E 1.425,0.625 1.907,0.802 0.482,0.177 10 Unlock 1.187,1.417 1.669,1.593 0.482,0.177 10 Lock 5.445,2.071 5.539,2.346 false 5.167,2.078 5.192,2.369 false 4.988,2.084 4.877,2.369 false

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
OFF 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω



If the result is not as specified, replace the door lock assembly.




Hide 69310 4.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144110E14
5.813,1.885 6.26,2.104 false 5.594,1.854 6.083,1.448 false 5.51,2.063 5.615,2.396 false 5.365,2.063 5.167,2.406 false 5.25,1.813 4.708,1.313 false 5.021,1.885 4.51,2.208 false 1.625,2.281 2,2.448 0.375,0.167 10 false Lock 0.792,1.969 1.302,2.146 0.51,0.177 10 false Unlock 3.969,0.375 6.458,0.74 2.49,0.365 10 false Component without harness connected: (Front Door Lock RH) 6.125,1.344 6.333,1.531 0.208,0.188 10 false L 6.313,2.031 6.615,2.208 0.302,0.177 10 false UL 5.49,2.406 5.885,2.646 0.396,0.24 10 false LSSR 5.104,2.406 5.292,2.615 0.188,0.208 10 false E 4.313,2.146 4.594,2.313 0.281,0.167 10 false DL 4.323,1.219 4.781,1.417 0.458,0.198 10 false UNDL

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Set
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unset


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the door lock assembly.




c.

for RHD:

B144105E02
4.045,0.263 6.673,0.845 2.628,0.582 10 Component without harness connected: (Front Door Lock RH) 5.796,2.369 6.028,2.537 0.232,0.168 10 UL 5.54,2.369 5.773,2.537 0.232,0.168 10 L 4.976,2.369 5.209,2.537 0.232,0.168 10 E 5.251,2.094 5.011,2.352 false 5.568,2.348 5.568,2.096 false 5.752,2.082 5.873,2.348 false 1.425,0.625 1.907,0.802 0.482,0.177 10 Unlock 1.187,1.417 1.669,1.593 0.482,0.177 10 Lock

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
OFF 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω



If the result is not as specified, replace the door lock assembly.