Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255542 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184440E13
5.677,1.844 6.146,2.104 false 4.958,1.844 4.469,2.094 false 5.104,2.052 4.938,2.385 false 5.521,2.031 5.604,2.344 false 1.823,2.167 2.313,2.333 0.49,0.167 10 false Unlock 0.927,2.021 1.323,2.208 0.396,0.188 10 false Lock 4.167,0.281 6.677,0.635 2.51,0.354 10 false Component without harness connected: (Rear Door Lock LH) 6.177,2.042 6.427,2.229 0.25,0.188 10 false UL 4.375,2.031 4.573,2.229 0.198,0.198 10 false L 5.479,2.417 5.917,2.656 0.438,0.24 10 false LSSR 4.885,2.417 5.052,2.625 0.167,0.208 10 false E

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
6 (LSSR) - 9 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.




Hide 69340 2.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144119E04
1.882,2.1 2.374,2.263 0.492,0.163 10 Unlock 1.076,2.093 1.474,2.277 0.397,0.184 10 Lock 4.028,0.349 6.542,0.707 2.514,0.358 10 Component without harness connected: (Rear Door Lock LH) 6.026,1.868 6.279,2.056 0.253,0.188 10 UL 5.973,1.404 6.166,1.597 0.193,0.193 10 L 5.554,1.834 6.011,1.918 false 5.357,1.796 5.932,1.502 false 5.95,2.237 6.434,2.497 0.485,0.260 10 LSSR 5.432,2.335 5.597,2.514 0.165,0.179 10 E 5.445,2.007 5.481,2.307 false 5.582,2.004 5.929,2.291 false 4.064,1.207 4.557,1.405 0.493,0.198 10 UNDL 4.162,1.953 4.405,2.119 0.243,0.166 10 DL 5.038,1.757 4.467,1.27 false 4.81,1.778 4.39,2.006 false

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Set
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unset


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (LSSR) - 6 (E) Unlock Below 1 Ω
5 (LSSR) - 6 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.




Hide 69330 3.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184441E14
5.823,1.833 6.271,1.99 false 5.031,1.823 4.583,1.979 false 5.688,2.031 5.781,2.354 false 5.188,2.031 5.094,2.354 false 2.448,2.01 2.802,2.167 0.354,0.156 10 false Lock 1.49,2.135 1.969,2.292 0.479,0.156 10 false Unlock 4.083,0.229 6.583,0.573 2.5,0.344 10 false Component without harness connected: (Rear Door Lock RH) 6.313,1.906 6.563,2.083 0.25,0.177 10 false UL 4.479,1.906 4.719,2.063 0.24,0.156 10 false L 5.635,2.396 6.094,2.656 0.458,0.26 10 false LSSR 5.042,2.365 5.198,2.563 0.156,0.198 10 false E

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
6 (LSSR) - 9 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.




Hide 69330 4.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144120E11
4.792,1.865 4.208,2.094 false 5.958,2.156 5.563,1.865 false 4.99,2.031 5.208,2.406 false 4.792,2.052 4.635,2.417 false 5.021,1.792 4.333,1.427 false 5.344,1.792 5.979,1.281 false 3.896,0.177 6.396,0.51 2.5,0.333 10 false Component without harness connected: (Rear Door Lock RH) 4.104,2.021 4.281,2.219 0.177,0.198 10 false L 4.115,1.365 4.385,1.542 0.271,0.177 10 false UL 1.99,2.083 2.521,2.24 0.531,0.156 10 false Lock 1.104,2.063 1.844,2.219 0.74,0.156 10 false Unlock 5.031,2.438 5.479,2.635 0.448,0.198 10 false LSSR 4.583,2.427 4.854,2.646 0.271,0.219 10 false E 5.969,2.104 6.49,2.385 0.521,0.281 10 false UNDL 6.031,1.198 6.313,1.375 0.281,0.177 10 false DL

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Set
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unset


If the result is not as specified, replace the door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
6 (LSSR) - 9 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the door lock assembly.